how to replace lawn mower pull cord

How to Replace a Lawn Mower Pull Cord

By David Taylor
AD

If your loyal lawn mower has been letting you down lately, dragging its feet with a weak or broken pull cord, it might be time for a replacement. Don't let this minor setback put a damper on your gardening plans. With a little know-how and the right tools, reviving your lawn mower is a breeze. Let's dive in and learn how to replace a lawn mower pull cord, step by step.

First things first, safety comes first. Always disconnect the spark plug wire before you begin any work on your lawn mower to prevent accidental starts. Now, let's gather our tools. You'll need a new pull cord, a flathead screwdriver, needle-nose pliers, and possibly a wrench, depending on your mower's model.

Understanding Your Lawn Mower's Pull Cord

Before we start, let's understand the components of your mower's pull cord system. There's the pull cord itself, a spring that provides tension, a pulley system, and a cable that connects to the mower's starter mechanism. By replacing the pull cord, you'll ensure smooth starting and extend the life of your mower.

AD
How To Replace A Lawn Mower Starter Cord
How To Replace A Lawn Mower Starter Cord
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
DIY Toro Pull Cord Repair – Easy Step-by-Step Instructions
DIY Toro Pull Cord Repair – Easy Step-by-Step Instructions

Replacement cords are available in various materials like cotton or plastic, each with its pros and cons. For most users, a basic cotton cord works just fine. Always ensure you choose a cord compatible with your mower's make and model.

Measuring the Correct Cord Length

Start by measuring the old pull cord to determine the length needed for a replacement. Most residential mowers require a cord between 12 to 24 inches in length. Ensure you measure from the starting point of the pull cord to the tip, not accounting for any excess cord that may be coiled inside the mower's housing.

How to Repair a Lawn Mower Pull Cord
How to Repair a Lawn Mower Pull Cord
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com

To confirm your measurement, lay the old cord across the new one, making sure the splicing ends match up. If the new cord is longer, that's okay – you can trim it down later.

Determining Pull Cord Direction

Before you begin, look at the existing pull cord. You'll notice that it's wound in a specific direction. This is crucial as it dictates the pull cord's exit point from the mower. The cord should unwind smoothly and not get tangled or contradictory during use. Make a mental note or even mark the direction for reference during installation.

AD

Now that you've covered the basics, let's move on to replacing the pull cord. The process varies slightly based on mower models, so consult your user manual if available. Here, we'll provide a general step-by-step guide.

Replacing the Lawn Mower Pull Cord

First, locate the pull cord Housing – it's usually near the mower's handlebars. Using your screwdriver, gently pry off the cover to expose the pulley system and the spring.

Next, carefully compress the spring using your screwdriver. Be cautious here, as the spring can cause injuries if it snaps back suddenly. With the spring held in place, remove the retaining clip or nut that secures the old pull cord. This should free up the cord, allowing you to pull it out.

AD

Splicing the New Pull Cord

Before installing the new cord, you'll need to splice it. A simple overhand knot works best for this. Fold the end of the new cord over about an inch and a half, then insert the folded part through the loop, pulling it tightly. This will create a small, reinforced eyelet that will fit onto the pulley system's hook.

Once spliced, insert the new cord into the mower housing, ensuring it's facing the correct direction. Place the retained clip or nut back on and releases the spring. It should now be securely holding the new cord in place. Replace the Housing cover, and your mower is ready for a test pull.

Retensioning the Pull Cord

Your mower's pull cord should now be neatly coiled, ready for use. However, you might need to retension it. With the mower on a flat surface, pull the cord fully out until it's taut. Hold it at this point for about 10-15 seconds to allow the spring to adjust. Slowly release the cord, letting it coil back in. Repeat this process a few times to ensure the cord is fully tensioned.

AD

Okay, you're done! Before you start your mower, give the pull cord a few gentle tugs to ensure it's working properly. Then, reconnect the spark plug wire and fire up your mower. You've just successfully replaced a lawn mower pull cord – great job!

Regularly maintaining your mower is key to prolonging its lifespan. By keeping the blades sharpened and the air filter clean, you'll also reduce the strain on the pull cord, ensuring you won't have to replace it anytime soon. Now get out there and tame that lawn!

AD