how to replace craftsman lawn mower pull cord

Step-by-Step: Fixing a Craftsman Lawn Mower Pull Cord

By Laura Jackson
AD

Is your Craftsman lawn mower not starting due to a snapped or frayed pull cord? Fret not, as you can easily replace the pull cord yourself, saving you time and money. Follow this step-by-step guide to replace your Craftsman lawn mower pull cord and get your lawn back in shape.

Before you begin, make sure to identify the right type of pull cord for your specific Craftsman lawn mower model. Although Craftsman uses a standard 3/8" rope, the length and end type (loop or straight) may vary. Always consult your mower's user manual or contact Craftsman's customer support if you're unsure.

Preparation: Gather Tools and Materials

To replace the pull cord on your Craftsman lawn mower, you'll need a few essential tools and materials:

AD
How To Replace A Lawn Mower Starter Cord
How To Replace A Lawn Mower Starter Cord
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How To Replace Pull Cord On Lawn Mower?
How To Replace Pull Cord On Lawn Mower?

  • New pull cord (3/8" diameter, with the correct length and end type)
  • Screwdriver (Philips or flathead, depending on your mower model)
  • Needle-nose pliers
  • Ratchet strap or bungee cord (optional, for securing the mower)

How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
Craftsman Lawnmower Tune Up and Pull Cord Replace
Craftsman Lawnmower Tune Up and Pull Cord Replace

Safety First: Secure and Drain the Mower

Before you start, ensure your safety by securing your mower and draining any fuel from the tank. If you have a riding lawn mower, use a ratchet strap or bungee cord to tie the machine down to prevent it from moving during the replacement process.

For both push and riding mowers, carefully drain the fuel tank by following the manual's instructions. This step is crucial to prevent any accidental fuel spills or fires while working on the mower.

AD

Access the Reel and Pull Cord

To access the pull cord reel, follow these steps:

  1. Tip the mower onto its side, ensuring the air filter is facing up to prevent any debris from entering.
  2. Remove the cap or cover that protects the pull cord reel. The Location and removal process may differ depending on your mower model, so consult your manual if needed.
  3. Once you've exposed the reel, you should see the snapped or frayed pull cord wound around it.

AD

Removing the Old Pull Cord

With the reel exposed, you can now remove the old pull cord. Follow these steps:

  • Gently unravel the old pull cord from the reel, ensuring you don't damage the rewinding mechanism.
  • Once you've unwound the cord, use needle-nose pliers to carefully pull the old cord out of the mower, guiding it through the hole from which it originally emerged.
  • Discard the old pull cord, and make sure to clean any debris or remaining cord pieces from the mower to prevent any interference with the new cord.

AD

Preparing the New Pull Cord

Before installing the new pull cord, you'll need to prepare it:

  • Measure and cut the new pull cord to the appropriate length, ensuring it's long enough to easily reach the pull handle but not so long that it tangles or causes other issues.
  • If your mower requires a loop end, create a loop at one end of the new pull cord using a lark's head knot or by folding the rope onto itself and tying a secure knot.

Installing the New Pull Cord

With the new pull cord prepared, you can now install it on the mower:

  1. Feed the new pull cord through the hole where the old cord was removed, using the needle-nose pliers to help guide it through if necessary.
  2. Wrap the new pull cord around the reel, ensuring it's wound evenly and not overlapping or bunching up in any spots. The specific rewinding process may depend on your mower model, so consult your manual if needed.
  3. Once you've rewound the cord, reattach the cord to the pull handle. If your mower has a specific slot or mechanism for this purpose, ensure you follow the correct procedure outlined in your manual.

Reassemble and Test the Mower

Now that you've replaced the pull cord and ensured everything is installed correctly, it's time to reassemble your mower and test it:

  • Carefully tip the mower back onto its wheels if you've tipped it onto its side.
  • Securely reattach the protective cap or cover over the pull cord reel.
  • If you've drained the fuel, refill the tank with fresh gasoline, ensuring you follow the proper mixing instructions if your mower requires an oil-gasoline mix.
  • Inspect your mower to ensure everything is properly reattached and secured before starting it.
  • Pull the cord gently but firmly several times to start the mower. If everything is functioning correctly, the engine should begin after a few pulls.

Regular Maintenance and Care

To minimize the risk of future pull cord issues, follow these regular maintenance tips:

  • Inspect the pull cord before each use for any signs of wear or damage.
  • Clean the mower regularly to prevent debris buildup, which can cause the cord to fray or break due to excessive wear.
  • Store your mower in a dry, cool place when not in use to protect the pull cord from damage caused by extreme temperatures or humidity.

Congratulations! You've successfully replaced the pull cord on your Craftsman lawn mower. With your mower back in working order, you're ready to tackle your lawn care tasks with confidence and ease. Happy mowing!

AD