how to replace pull cord on honda lawn mower

Easy Steps: Replace Pull Cord on Honda Lawn Mower

By Amanda Martin
AD

Tending to your Honda lawn mower ensures it's always ready to tackle your lawn's needs. One common issue is a worn-out or broken pull cord, which can make starting your mower challenging. Don't let a minor issue like this stop you from maintaining a vibrant lawn. Here's a step-by-step guide on how to replace a pull cord on your Honda lawn mower.

Before you start, gather your tools: a new pull cord (ensure it's compatible with your mower model), a flathead screwdriver, needlenose pliers, and a ratchet set. You'll also need a small amount of lubricant like engine oil or WD-40 to ensure smooth operation of the new cord.

Preparation

Before diving into the replacement process, make sure your mower is off and has cooled down completely to prevent any injuries.

AD
How To Replace A Lawn Mower Starter Cord
How To Replace A Lawn Mower Starter Cord
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How To Replace Pull Cord On Lawn Mower?
How To Replace Pull Cord On Lawn Mower?

Next, remove any protective covers or guards that might interfere with your work. For safety, disconnect the spark plug wire to prevent accidental starting while you're working on the mower.

Removing the Old Pull Cord

Start by locating the pull cord housing on the mower. It's usually a plastic or metal cover that protects the cord and pulley system. Remove any screws securing the housing in place using your ratchet set.

a man is working on a lawn mower
a man is working on a lawn mower
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com
How to Replace a Pull Cord on Lawn Mower - A beginners guide | Lawnmowerfixed.com

With the housing removed, identify the old pull cord. It might be broken or frayed, making it easier to remove. Use your needlenose pliers to gently pull the cord out from thepulley, being careful not to damage the pulley itself. If the cord is firmly stuck, you might need to use a little lubricant to help it along.

Preparing the New Pull Cord

Before installing the new cord, make sure it's the correct type and length for your mower. Honda mowers typically use a specific type of pull cord, so ensure you've got the right one.

AD

Cut the new cord to the appropriate length. It's better to cut it slightly longer than needed and trim it after installation to ensure it doesn't catch on anything while starting the mower.

Installing the New Pull Cord

Now that you've prepared the new cord, it's time to install it. Insert one end of the cord into the pulley system, ensuring it's snapped back into place securely.

Lubricate the cord slightly with engine oil or WD-40 to help it slide through the system and ensure smooth operation.

AD

Threading the Cord

Begin threading the cord through the pulley system and the handle. Guide it carefully, ensuring it's not kinking or looping excessively, which could limit its effectiveness when pulling the cord to start the mower.

Once the cord is completely threaded through the system, pull gently on both ends to ensure it's seated correctly and moving smoothly through the pulley system.

Securing the Cord

Gently pull on the cord to remove any slack. Tie a knot at the end of the cord to prevent it from retracting back into the mower. Ensure the knot is secured tightly and won't come undone over time.

AD

Wrap the excess cord around the handle a few times, securing it with tape to keep it from getting tangled or caught on anything. Once the cord is all the way out and secured, your mower's pull cord is ready to use.

After reassembling the pull cord housing and allowing the lubricant to set, you can now reconnect the spark plug wire and try starting your mower. With your newly replaced pull cord, your Honda lawn mower should start with ease once again.

AD