how to fix weed eater pull string

"Step-by-Step: How to Fix Weed Eater Pull String"

By Sarah Miller
AD

Experiencing trouble with your weed eater's pull string? You're not alone. This common issue can make starting your trimmer a chore, but don't let it get you down. With a few simple steps, you can fix your weed eater's pull string and get back to tidying your lawn in no time. Let's dive in and tackle this problem head-on.

Before we begin, it's essential to ensure safety first. Always unplug your weed eater or remove the battery before performing any maintenance. Now, let's address those broken or difficult-to-pull strings.

Understanding Your Weed Eater's Pull String

First, let's gain a better understanding of your weed eater's pull string, also known as the fuel line. This cord is responsible for igniting the engine when you pull it. A properly functioning pull string should snap back after you release it, ready for the next pull.

AD
How to fix weed eater starter recoil spring & pull string.
How to fix weed eater starter recoil spring & pull string.
Fastest Way to String Weed Eater
Fastest Way to String Weed Eater
How To Troubleshoot And Repair A Weed Eater Pull Cord - Hunker
How To Troubleshoot And Repair A Weed Eater Pull Cord - Hunker

However, repeated use and wear can cause this string to fray, break, or stick, leading to starting difficulties. Knowing how to replace or fix this crucial component will save you time and money in the long run.

Identifying Common Pull String Issues

Before you start tinkering with your weed eater, you need to identify the root of the problem. The most common pull string issues include:

HOW TO STRING DOUBLE-HEADED WEED EATERS #shorts
HOW TO STRING DOUBLE-HEADED WEED EATERS #shorts
113K views · 1.9K reactions | String weedeater. Line trimmer whatever you want to call it #jmg8tor | By jmg8tor | So I'm going to go over putting string on your weed eater. Seems so simple. Lots of people have problems with it. Here's what I'm going to tell you. Most of them are going to look like this. You have to take this little piece off. You pull the little piece out here. The string goes on. You actually wrap your string around this. But I'mma tell you don't do that. When you take this off just take this whole head off. It's like that. You don't need it. Okay? And replace it with one like this that winds it up itself. Then you just cut your piece of string. I like to cut it you know about four or five feet long. You find the hole okay? And you just push the string straight through the hole until it comes out the other side, alright? Or you try to once that happens okay and you get it out here just like this you just pull it off level alright and then you just wind this top part if you hold it with your hand you just turn this top piece just like this and you just keep turning this thing until it pulls all the cord up exactly where you need it and then you don't ever have to worry about it there and you're done you bump it it comes out just like normal so take your old weed eater head replace it with one of these alright then next
113K views · 1.9K reactions | String weedeater. Line trimmer whatever you want to call it #jmg8tor | By jmg8tor | So I'm going to go over putting string on your weed eater. Seems so simple. Lots of people have problems with it. Here's what I'm going to tell you. Most of them are going to look like this. You have to take this little piece off. You pull the little piece out here. The string goes on. You actually wrap your string around this. But I'mma tell you don't do that. When you take this off just take this whole head off. It's like that. You don't need it. Okay? And replace it with one like this that winds it up itself. Then you just cut your piece of string. I like to cut it you know about four or five feet long. You find the hole okay? And you just push the string straight through the hole until it comes out the other side, alright? Or you try to once that happens okay and you get it out here just like this you just pull it off level alright and then you just wind this top part if you hold it with your hand you just turn this top piece just like this and you just keep turning this thing until it pulls all the cord up exactly where you need it and then you don't ever have to worry about it there and you're done you bump it it comes out just like normal so take your old weed eater head replace it with one of these alright then next
  • Broken or frayed string
  • String that doesn't retract after being pulled
  • Difficult or impossible to pull the string
  • String sticks or catches during operation

Gathering Tools and Materials

Depending on the issue, you may need to replace or repair the pull string. Here's a list of tools and materials you might need:

  • New pull string (ensure it matches your weed eater's model)
  • Pliers or needle-nose pliers
  • Scissors
  • Flashlight (to help see inside your weed eater)
  • Rubber gloves

Troubleshooting and Fixing Pull String Issues

Now that you're armed with knowledge and tools, let's address those pesky pull string problems.

AD

Replace a Broken or Frayed Pull String

If your pull string is broken, frayed, or too short to grasp, it's time for a replacement.

  1. Unplug your weed eater and remove the spark plug wire (if gasoline-powered) to prevent accidental starting.
  2. Locate the string access hole on your weed eater. This is usually covered by a small cap or screw.
  3. Remove the cover, and use a flashlight to locate the string's end inside the housing.
  4. Pull on the string until you have a decent length (around 9-12 inches) to grasp.
  5. Use scissors or pliers to cut the string close to the engine housing.
  6. Thread one end of the new string through the access hole and tie it to the old string's remaining end.
  7. Pull the new string through the housing until you have about 6-8 inches on the outside.
  8. Reassemble the weed eater, replace the spark plug wire (if applicable), and test the new string by pulling it gently.

Addressing a Non-Retracting Pull String

A pull string that doesn't snap back after releasing it is likelybent, trapped, or the return spring is damaged. Here's how to address this issue:

  • Inspect the string for kinks or signs of wear. If the string is bent, straighten it gently using pliers.
  • Check if the string is lodged or trapped somewhere inside the weed eater. If so, free it carefully.
  • Inspect the return spring. If it's damaged or broken, replace it following your weed eater's manufacturer guidelines.

Dealing with a Hard-to-Pull or Sticking String

Difficult-to-pull or sticking strings can be caused by dirt, grease, or an over-tightened spring. Here's how to address these problems:

AD
  • Clean the internal components of your weed eater, focusing on the string's path. Use a suitable cleaning solution and compressed air to ensure a smooth operation.
  • Inspect the return spring. If it's too tight, adjust it following your weed eater's manufacturer guidelines to achieve the correct tension.

With a little elbow grease and some basic tools, you should now be able to fix your weed eater's pull string and get back to those overgrown weeds. If you're still having trouble, don't hesitate to consult your weed eater's owner's manual or contact a professional for further assistance. Happy trimming!

AD