how to fix a weed eater pull string

Fix Your Weed Eater: A Simple Guide to Replacing Your Weed Eater's Pull Cord

By Christopher Lewis
AD

Has your weed eater's starting cord snapped or extended excessively, leaving it useless? Fear not, for this issue is easily rectifiable. Here's your comprehensive guide on how to fix a weed eater pull string, complete with illustrated steps and detailed explanations.

Before you start, ensure you're equipped with the right tools: a new starting cord, needle-nose pliers, a flathead screwdriver, and a power drill with a drill bit slightly smaller than the cord's diameter. Safety first: unplug the tool and let it cool before proceeding.

Investigating the Damage

Begin by inspecting the pulley system under the weed eater's housing. The starting cord should be firmly attached to this pulley. If it's snapped or detached, that's where you'll repair it.

AD
How to fix weed eater starter recoil spring & pull string.
How to fix weed eater starter recoil spring & pull string.
a man wearing sunglasses is holding an object in his hand and taking a picture with the phone
a man wearing sunglasses is holding an object in his hand and taking a picture with the phone
How to string up a weed eater with an echo speed feed head #mowing #landscaping#pov #echo #echotools
How to string up a weed eater with an echo speed feed head #mowing #landscaping#pov #echo #echotools

The cord should run through an eyelet or hole in the weed eater's housing and be securely tied to the pulley. If it's not, or the cord is excessively long, you'll need to shorten it and reattach it.

Disassembling the Housing

Using a flathead screwdriver, carefully pry off the lower housing of your weed eater. On some models, you may need to remove a few screws first.

113K views · 1.9K reactions | String weedeater. Line trimmer whatever you want to call it #jmg8tor | By jmg8tor | So I'm going to go over putting string on your weed eater. Seems so simple. Lots of people have problems with it. Here's what I'm going to tell you. Most of them are going to look like this. You have to take this little piece off. You pull the little piece out here. The string goes on. You actually wrap your string around this. But I'mma tell you don't do that. When you take this off just take this whole head off. It's like that. You don't need it. Okay? And replace it with one like this that winds it up itself. Then you just cut your piece of string. I like to cut it you know about four or five feet long. You find the hole okay? And you just push the string straight through the hole until it comes out the other side, alright? Or you try to once that happens okay and you get it out here just like this you just pull it off level alright and then you just wind this top part if you hold it with your hand you just turn this top piece just like this and you just keep turning this thing until it pulls all the cord up exactly where you need it and then you don't ever have to worry about it there and you're done you bump it it comes out just like normal so take your old weed eater head replace it with one of these alright then next
113K views · 1.9K reactions | String weedeater. Line trimmer whatever you want to call it #jmg8tor | By jmg8tor | So I'm going to go over putting string on your weed eater. Seems so simple. Lots of people have problems with it. Here's what I'm going to tell you. Most of them are going to look like this. You have to take this little piece off. You pull the little piece out here. The string goes on. You actually wrap your string around this. But I'mma tell you don't do that. When you take this off just take this whole head off. It's like that. You don't need it. Okay? And replace it with one like this that winds it up itself. Then you just cut your piece of string. I like to cut it you know about four or five feet long. You find the hole okay? And you just push the string straight through the hole until it comes out the other side, alright? Or you try to once that happens okay and you get it out here just like this you just pull it off level alright and then you just wind this top part if you hold it with your hand you just turn this top piece just like this and you just keep turning this thing until it pulls all the cord up exactly where you need it and then you don't ever have to worry about it there and you're done you bump it it comes out just like normal so take your old weed eater head replace it with one of these alright then next
How To Troubleshoot And Repair A Weed Eater Pull Cord - Hunker
How To Troubleshoot And Repair A Weed Eater Pull Cord - Hunker

Set the housing aside and locate the pulley. It's usually visible through a hole in the housing, with the starting cord attached to it. If the cord is snapped or detached, you'll need to replace it.

Removing the Old Cord

Insert the needle-nose pliers through the hole in the housing and use them to pull the old cord out. If the cord is snapped off near the pulley, you may need to drill a small hole in the center of the pulley to thread the pliers through.

AD

Once you've removed the old cord, use the needle-nose pliers to remove the old knot from the pulley. Be careful not to damage the pulley's groove.

Replacing the Starting Cord

Your new starting cord should be the same type and length as the old one. Typical weed eater cords are made of nylon and are about 50-60 inches long.

Using your power drill, create a hole in the center of the new cord's end loop. This will make it easier to thread the cord through the pulley and housing.

AD

Threading the New Cord

Starting from the pulley, thread the new cord through the pulley's hole, then through the housing's eyelet or hole. The hole in the cord's end loop should make this process easier.

Once the cord is threaded, pull it through the housing until about 2-3 inches of cord stick out from under the housing.

Securing the Cord

Using the needle-nose pliers, create a small loop in the end of the cord. Slide the loop onto the pulley groove, ensuring it's secure and won't slip off.

AD

Tighten the loop around the pulley by pulling on the cord with the pliers. Then, tie a quick knot in the cord to keep it in place. You can now trim the excess cord with scissors, leaving about 1 inch of cord sticking out from under the housing.

Reassembling the Weed Eater

Once you've secured the new starting cord, carefully align the housing back onto the weed eater's base. If your housing had screws, replace them now.

Gently pull the starting cord to test the repair. The weed eater should now start with ease. Plug it in and give it a test run to ensure it's working properly.

Regularly inspecting your weed eater's starting cord can prevent this issue in the future. With this guide, you're now equipped to fix a weed eater pull string whenever the need arises. Happy gardening!

AD