toro weed eater how to replace string

Toro Weed Eater: Step-by-Step Guide to Replace String

By John Garcia
AD

Toro weed eaters are known for their durability and performance, but like any other tool, they require maintenance, especially when it comes to replacing the trimmer line or string. If you're here, you're likely wondering how to replace the string on your Toro Weed Eater. Don't worry; we've got you covered. This guide will walk you through the process step by step.

Before we dive into the process, it's essential to understand that different Toro weed eaters might have slight variations in their design. The general process, however, remains the same. So, let's get started!

Preparation: Gather Your Tools

Before you begin, ensure you have all the necessary tools. You'll need a new spool of string designed for your Toro Weed Eater, a Phillips screwdriver, and a pair of scissors or a knife for cutting the string to size.

AD
a man wearing sunglasses is holding an object in his hand and taking a picture with the phone
a man wearing sunglasses is holding an object in his hand and taking a picture with the phone
a man is holding an object in his hand and pointing to it with the words replace string
a man is holding an object in his hand and pointing to it with the words replace string
HOW TO Re-String A Weedeater Grass Trimmer
HOW TO Re-String A Weedeater Grass Trimmer

Safety is paramount when working with string trimmers. Make sure to unplug your Toro Weed Eater from any power source before you start. Also, wear safety glasses to protect your eyes from any debris.

Identifying the String Feed System

Toro weed eaters typically use one of two string feed systems: the Auto Spool or the BumpFeed system. Identifying the system on your tool is the first step toward successful string replacement.

Replace the line in your string trimmer!
Replace the line in your string trimmer!

If your Toro Weed Eater has a large,anjty and thick spool of string, it's likely an Auto Spool model. If the spool is smaller and slimmer, with a tabs or buttons around the bottom, it's probably a BumpFeed model.

Replacing the String on an Auto Spool Toro Weed Eater

If your Toro Weed Eater uses the Auto Spool system, follow these steps to replace the string:

AD
  1. Unplug your Toro Weed Eater and lay it on its side with the cutting head up.
  2. Using a Phillips screwdriver, remove the screw from the center of the cutting head cover.
  3. Carefully pull off the cover to expose the spool.
  4. Once the cover is off, grasp the spool with one hand and turn the trimmer head counterclockwise to unwind the old string.
  5. When all the old string is off, cut the remaining string on the spool short. Then, take your new string and insert one end into the hole on the spool.
  6. Wind the string evenly onto the spool, ensuring it's tight and even. Leave enough string to extend out of the trimmer head when you're done - about 6 to 8 inches should suffice.
  7. Replace the head cover and push the button down to advance the new string. Then, secure the cover with the screw.
  8. Plug in your Toro Weed Eater and cut the excess string from the end with scissors or a knife.

Replacing the String on a BumpFeed Toro Weed Eater

If your Toro Weed Eater uses the BumpFeed system, follow these steps:

  1. Unplug your Toro Weed Eater, remove the guard, and lay it on its side with the cutting head up.
  2. Using a Phillips screwdriver, remove the two screws that secure the trimmer head cover in place.
  3. Remove the cover to reveal the spool. You might need to lift tabs on the sides of the spool to release it.
  4. Unroll the old string from the spool. Once it's all off, cut the remaining string from the spool.
  5. Take your new string and insert one end into the hole on the spool. Wind the string evenly around the spool, leaving about 6 to 8 inches of string at the end.
  6. Reinstall the spool into the trimmer head, ensuring the tabs clip into place. Replace the head cover and secure it with the screws.
  7. Turn the trimmer head counterclockwise to wind the string into the head. Pull out the new string from the bottom of the tool to set the line.
  8. Plug in your Toro Weed Eater and cut the excess string from the end.

Congratulations! You've successfully replaced the string on your Toro Weed Eater. Regular maintenance, like these string replacements, will ensure your tool runs smoothly and extends its lifespan. Don't forget to store your Toro Weed Eater properly when not in use. Happy trimming!

AD