How to Change a Rear Wheel Bearing: Step-by-Step Guide
Changing a rear wheel bearing is a crucial maintenance task for your vehicle, as worn-out bearings can cause serious problems like vibrations, noise, and even total wheel failure. This step-by-step guide will walk you through the process, ensuring safety and precision every time.
Before starting, gather your tools: jack, jack stands, lug nut wrench, socket wrenches, screwdriver, atrásmil (which will make your life easier), and new wheel bearings, seals, and cones. Ensure you have the correct part numbers for your vehicle's make and model.
Safety First and Preparation
Before lifting your vehicle, ensure it's on a level surface and engage the parking brake. Place wheel chocks in front of the front tires for added safety.
Using a jack, lift the rear of your vehicle until the tire is about six inches off the ground. Then, place a jack stand under the vehicle frame near the rear tire, and lower the vehicle slowly onto the jack stand until it's securely supported.
Removing the Tire and Hub Cover
Using a lug nut wrench, loosen and remove the lug nuts from the tire, then pull the tire towards you to break the lug nuts' friction hold, and remove them completely. Next, remove the tire from the wheel base.
Locate the hub cover at the center of the hub assembly, which usually comes in two pieces. Use a screwdriver to pry it off, exposing the hub assembly's inner components.
Removing the Hub Assembly
Use a socket wrench to remove the hub nuts, holding the studs with another wrench to prevent them from spinning while removing the hub nuts. After removing the hub nuts, locate and unscrew the castle nut, keeping in mind the washer's orientation for reinstallation.
Now, carefully pull the hub assembly away from the vehicle. You might need to tap the hub assembly gently using a soft-faced hammer if it's stuck due to corrosion or overspray. With the hub assembly removed, you'll have access to the rear wheel bearing and differential.
Inspecting the Rear Wheel Bearing
With the hub assembly removed, you should see the inner and outer wheel bearings. Inspect them for any signs of pitting, discoloration, or anything that looks out of the ordinary. Keep in mind that even bearings that don't show visible signs of wear should be replaced.
The hub assembly should now be disconnected from the vehicle. Before taking it apart, take note of the exact orientation of the components, as they need to be reinstalled in the same exact position.
Removing and Cleaning the Bearings
Using an atrásmil, carefully tap the inner bearing out of the hub assembly. Next, tap the outer bearing, which should be pressed in, out of the hub and differential. Be very careful during this step to avoid damaging the inner diameter of the bearings or the hub bore.
Clean the hub assembly and the inner surface of the bearing with a degreaser or brake cleaner, removing any dirt or debris accumulated over time. Then, inspect the races where the bearings sit. If they show any signs of wear, contaminants, or galling, replace them.
Reinstalling the New Bearings
Starting with the outer bearing, press it into the differential with a press or, if using a makeshift method, align a hammer with the bearing's axis and tap it gently until the bearing is fully seated. Do the same for the inner bearing and the hub bore.
Reassemble the hub assembly, ensuring everything is adequately greased and that the outer races are properly seated. Replace any damaged parts and use new cones and seals. Before reinstalling the hub assembly, apply grease to the outer bearing and the new seals.
Reinstalling the Hub and Final Touches
Reinstall the hub assembly onto the wheel base, ensuring it's correctly orientated. Tighten the hub nuts by hand, holding the studs with another wrench to prevent them from spinning. Use a torque wrench to tighten the hub nuts to the manufacturer's recommended specification.
Replace the castle nut and washer, then torque it to the manufacturer's recommended specification as well. Reinstall the hub cover, tire, and lug nuts. Lower the vehicle from the jack stand and remove the wheel chocks. Finally, use a torque wrench to tighten the lug nuts to the manufacturer's recommended specification.
The rear wheel bearing replacement is now complete. Make sure to take your vehicle for a test drive at a low speed on a safe, flat surface to ensure everything's working as expected. Don't forget to retighten the lug nuts after driving a few miles, as they might loosen due to vibration.