how to change wheel bearing hub

Step-by-Step Guide: How to Change Wheel Bearing Hub & Save Money

By John Davis
AD

Have you noticed your vehicle pulling to one side while driving, or heard an unusual grinding or humming noise coming from your wheels? These could be signs that your wheel bearing hub is failing and needs replacement. Replacing a wheel bearing hub is not an everyday DIY task, but with the right tools and step-by-step guidance, it's entirely possible to do it yourself. Let's dive into the process of changing a wheel bearing hub, optimizing your vehicle's safety, and potentially saving you a trip to the mechanic.

Before you begin, ensure you have the necessary tools and equipment. These typically include a jack, jack stands, lug wrench, sockets and wrenches, a breaker bar, hammer, slide hammer, PB Blaster or another penetrating oil, and necessary replacement parts. Always consult your vehicle's owner's manual for specific part numbers and procedures.

Preparation and Removing the Wheel

First, you need to lift your vehicle off the ground to access the hub. Using a jack, lift the car by placing it under the vehicle's frame, close to the tire you'll be working on. Secure it with jack stands for safety. Next, break the lug nuts loose with your lug wrench, but don't remove them all the way yet.

AD
Easy Hub Bearing Removal Trick Without Special Tools
Easy Hub Bearing Removal Trick Without Special Tools
Replace and adjusting wheel bearings
Replace and adjusting wheel bearings
How to Replace a Rear Wheel Bearing in Your Car
How to Replace a Rear Wheel Bearing in Your Car

After securing the vehicle, completely remove the lug nuts and take off the tire. Now you'll have full access to the wheel bearing hub assembly.

Removing the Hub Assembly

Begin by removing the brake caliper. Use a hammer or breaker bar to carefully knock the caliper mounting bolts loose. With a wrench, unscrew them the rest of the way and pull the caliper off the rotor. If it's too tight, apply some penetrating oil around the bolts and let it sit for a few minutes.

a person holding a wrench in their right hand and working on an assembly piece
a person holding a wrench in their right hand and working on an assembly piece
How to Replace a Front Wheel Hub Bearing Assembly on 2014 Sierra \ Silverado Wheel Hub Replacement
How to Replace a Front Wheel Hub Bearing Assembly on 2014 Sierra \ Silverado Wheel Hub Replacement

Next, you'll need to remove the bearing itself. This usually involves tapping the hub with a hammer or using a slide hammer to slowly ease it out. If it's rusted or frozen in place, apply more penetrating oil and give it some time to work its magic.

Inspecting and Cleaning the Hub Assembly

While your new bearing is on its way, take the time to inspect the hub assembly and clean it thoroughly. Check the hub itself for signs of excessive wear, warping, or rust. If it's severely damaged, you may need to replace it as well. Additionally, clean any old grease or dirt off using a wire brush or cloth.

AD

After cleaning, spray the hub with a light coat of your new bearing's recommended grease. This will help create a barrier against moisture and further corrosion.

Installing the New Wheel Bearing Hub

Position your new bearing onto the hub, ensuring it's aligned correctly. When installing, be careful not to damage the bearing's seal. Tapping the assembly lightly with a hammer or using a slide hammer can help guide the bearing into place.

Now, reverse the disassembly process: reinstall the caliper, securing it with the mounting bolts. Next, reattach the tire and lug nuts, ensuring they're snug but not overly tight. Lower the vehicle and tighten the lug nuts further with the wrench. For safety, take the car for a test drive at low speeds to allow the new bearing to seat properly.

AD

Final Inspection and Torque Settings

After driving, recheck the lug nut torque and make any necessary adjustments. Consult your owner's manual for the correct torque specification, usually somewhere between 70-100 ft-lbs for most vehicles. If any lug nuts have moved or loosened, retighten them according to the specified torque.

Finally, listen for any unusual noises from your wheels. If everything is functioning correctly, you should hear a smooth, quiet rotation with no grinding, humming, or popping sounds. If you do, it might indicate that further inspection or adjustment is needed.

Regularly checking your wheel bearing hubs is crucial to maintaining your vehicle's safety and longevity. If you've performed this task diligently and correctly, you've not only saved money but also gained valuable knowledge about your vehicle's maintenance. The next time you hear an odd noise coming from your wheels, you'll know just what to do. If you're still unsure about any part of the process, don't hesitate to consult a professional mechanic for guidance. Safe driving!

AD
AD