Stringing a Weed Eater: Black & Decker Tricks - Step-by-Step Guide
Ah, the ubiquitous weed eater, or string trimmer as some like to call it, a garden's best friend in the war against unruly edges and stubborn weeds. If you've invested in a Black & Decker weed eater, congratulations! You've acquired a tool that combine's power and user-friendliness. But like all tools, it requires a little maintenance from time to time. Lo and behold, the humble string - it wears out, breaks, and generally needs replacing. So, let's dive into a step-by-step guide on how to string your Black & Decker weed eater like a pro.
First things first, safety. Before you start any maintenance, ensure your weed eater is unplugged from any power source. It's also a good idea to let the spool cool down if you've just used it. Now that we've covered the basics, let's get started.
Understanding Your Weed Eater's Spool
Before we dive into the nitty-gritty of stringing, it's crucial to understand what lies under the hood of your Black & Decker weed eater. Most models use a bump feed system, which means you can advance the line by bumping the head of the trimmer against the ground. The spool, or head, is where the line is housed and dispensed from.
Now that you're familiar with the anatomy let's move on to prepping your tool for astring change.
Removing the Old Spool
First, you'll want to remove any remaining line from the spool. This can usually be done by hand, but you might need to use a pair of pliers to grasp and pull the line if it's tough to remove. Once the old line is gone, you should see a hole in the center of the spool. This is where the shaft of your weed eater will fit.
Next, you'll want to remove the spool from the shaft. There are usually small tabs that you'll need to depress to release the spool. These tabs can be found on the outer edge of the spool. Once you've depressed the tabs, the spool should slide off the shaft easily.
Preparing the New Spool
Now that the old spool is off, it's time to prepare the new one. Most Black & Decker weed eaters use a fixed line length, so you'll need to measure out the correct amount of line for your model. The manual that came with your weed eater should specify the correct length.
Once you've measured out the right amount of line, you'll want to load it onto the spool. Start by feeding the line through the hole in the center of the spool. Then, wind the line around the spool in the direction indicated by the arrows or notches. Make sure to wind the line tightly against the previous layer to prevent tangling. Leave about 6-8 inches of line hanging off the end of the spool.
àRanging the New Spool
With your new spool loaded and ready, it's time to reinstall it onto your weed eater. First, insert the end of the shaft into the hole in the center of the spool. You may need to push down on the spool to get it to pop onto the shaft.
Once the spool is on the shaft, you'll need to reattach it to the body of the weed eater. This is usually done by lining up notches or tabs on the spool with corresponding holes or slots on the body of the weed eater. Make sure the spool is securely attached before you move on to the next step.
arning the Line
Now that your new spool is in place, it's time to string your weed eater. Start by pulling the excess line from the spool and feeding it through the eyelet on the trimmer head. Then, pull the line out through the hole on the underside of the trimmer head.
Next, you'll want to advance the line by bumping the head of the trimmer against the ground. This should feed more line out through the hole on the underside of the trimmer head. Continue bumping the head and feeding line until you have about 10-12 inches of line extending from the bottom of the head.
Setting the Trimmer Line Length
Finally, it's time to set the length of your trimmer line. Most Black & Decker weed eaters have a collapsible plastic outer guard that you can use to adjust the length of the line. Simply collapse the guard to the desired length to trim weeds, and extend it for more powerful cutting of thicker plants or grass.
And there you have it! You've successfully strung your Black & Decker weed eater and are ready to tackle those unruly edges in your garden. Remember to keep your trimmer clean and store it properly to ensure its longevity. Happy trimming!