How to String a Troy-Bilt Weed Eater: Step-by-Step Guide
Troy-Bilt weed eaters, with their robust design and reliable performance, are a staple among landscaping enthusiasts. However, like all tools, they require regular maintenance to ensure optimal functioning. One such maintenance task is properly stringing your Troy-Bilt weed eater. This process, while seemingly complex, can be easily mastered with the right guidance.
Before we dive into the process, it's crucial to understand that your Troy-Bilt weed eater model might vary, so always consult your user manual for specific instructions. However, the following guide provides a general step-by-step process that should apply to most Troy-Bilt models.
Gathering Necessary Supplies
Before you begin, ensure you have all the necessary supplies to string your Troy-Bilt weed eater. This includes a new spool of string, designed specifically for your Troy-Bilt model, and a pair of safety glasses to protect your eyes during the process.
Remember, using the incorrect type of string can damage your weed eater and void its warranty. Always use authentic Troy-Bilt string or a compatible aftermarket version recommended by your user manual.
Identifying the String Feed Side
Begin by identifying which side of your Troy-Bilt weed eater is the string feed side. Most weed eaters, including Troy-Bilt, feed string from the bottom. Look for an arrow or a line on the spool that points towards the center. This indicates the direction the string should feed out.
If you're unsure, consult your user manual or look up a video tutorial online. It's crucial to determine the correct side to avoid feeding the string incorrectly, which can lead to poor performance or damage to your tool.
Preparing the String
Unwind the required length of string from the spool. Most Troy-Bilt weed eaters require a string length ranging from 10 to 25 feet, depending on the model. Be sure to check your user manual for the correct length.
Once you've unwound the necessary length, cut the string into two equal pieces. This will make the stringing process easier and ensure that you have enough string for both sides of your weed eater.
Threading the String Through the Weed Eater
Now that you have your string prepared, it's time to thread it through your Troy-Bilt weed eater. Begin by removing the bump feed head, if your model has one. This is typically located at the bottom of the weed eater and can be easily unscrewed or released by pressing a button.
With the bump feed head removed, you'll see a small hole where the string will feed through. Take one of the string pieces and insert it into this hole, pulling it through until you have a few inches of string sticking out the other side. Repeat this process with the second piece of string.
Winding the String onto the Spool
Once you've fed both pieces of string through the hole, it's time to wind the string onto the spool. Start by placing the spool into the string housing in the correct direction - remember, the arrow or line on the spool should point towards the center.
Begin winding the string around the spool, making sure to keep it taut and neat. As you wind, ensure that the string does not overlap itself, as this can cause tangling and poor performance. Instead, wind the string in a neat, even pattern.
Leaving Enough String for the Head
As you near the end of the string, ensure that you leave enough string to pull through the bump feed head and out the trimmer head. A good rule of thumb is to leave about 6 to 8 inches of string on each side.
Once you've reached the end of the string, cut any excess off, leaving a small tab that you can easily grab onto.
Reassembling the Weed Eater
With the string wound onto the spool and enough left over for the trimmer head, it's time to reassemble your Troy-Bilt weed eater. Begin by replacing the bump feed head, ensuring that the string feeds out of the bottom as intended.
Next, pull the excess string through the trimmer head, leaving about 6 to 8 inches of string sticking out. This is the line that will trim your weeds. Trim this line to your desired length - most users leave it around 6 to 8 inches long.
Testing Your Trojan Work
With your Troy-Bilt weed eater reassembled and the string properly wound and trimmed, it's time to test your handiwork. Start by plugging in your weed eater and turning it on. As it starts up, pull the trigger to activate the string rotation.
Check that the string is feeding out smoothly and evenly. If it is, great! You've successfully strung your Troy-Bilt weed eater. If not, double-check your work and ensure that you've followed all the steps correctly.
Congratulations! You've just learned how to string your Troy-Bilt weed eater. With this newfound knowledge, you can ensure that your tool remains in top working condition, providing you with clean, efficient trimming seasons for years to come. Happy landscaping!