how to string troy bilt weed eater

How to Repair Troy-Bilt Weed Eater: Step-by-Step Guide

By David Clark
AD

Every homeowner knows the value of a well-maintained lawn, and a reliable weed eater, like the Troy-Bilt, is an essential tool in achieving that perfect yard. To maximize the lifespan of your Troy-Bilt weed eater and ensure it's ready to tackle those overgrown edges, you need to learn how to string your weed eater properly. Here's a step-by-step guide to help you master this DIY task.

Before we dive into the process, let's quickly discuss why keeping your Troy-Bilt weed eater's string in good condition is crucial. A properly strung weed eater performs better, lasts longer, and ensures safer operation. Now, let's get started with the main task at hand.

Understanding Your Weed Eater's Head

To string your Troy-Bilt weed eater correctly, it's essential to understand the components that make up its head. Familiarize yourself with the spool, the trim line, and how these parts interact. The spool holds the trim line, and when the spool rotates, the line feeds out, ensuring an even trim.

AD
How To Replace Troy Bilt Weed Wacker Line Replacing Weed Eater Wire Instructions
How To Replace Troy Bilt Weed Wacker Line Replacing Weed Eater Wire Instructions
HOW TO Re-String A Weedeater Grass Trimmer
HOW TO Re-String A Weedeater Grass Trimmer
How to restring RELOAD STRING on TORO 60V weed trimmer weedeater
How to restring RELOAD STRING on TORO 60V weed trimmer weedeater

Before you begin, ensure your Troy-Bilt weed eater is unplugged and there are no obstructions in the head. Also, gather any necessary tools, such as a flathead screwdriver or a trimmer line key, depending on your model.

Preparing the Weed Eater Head

First, you'll need to remove the head from the weed eater's shaft. Most Troy-Bilt weed eaters secure the head with a nut that can be turned counterclockwise by hand. If it's too tight, use your screwdriver to loosen it.

Once the nut is loose, pull the head gently towards you and turn it counterclockwise to unscrew it from the shaft. Keep the head and nut safe, as you'll need them later for reassembly.

Removing the Old Trimmer Line

Begin by removing the old trimmer line from the spool. You might find it easier to cut the old line off with scissors before proceeding. Then, pull the remaining pieces out of the head's eyelets and discard them.

AD

Inspect the spool for any signs of wear or damage. If the spool is in bad shape, it might be time to replace it. Clean the spool and any metal parts with a suitable lubricant, like WD-40, to keep them functioning smoothly.

Strings for Your Troy-Bilt Weed Eater

Troy-Bilt weed eaters typically accept spool-mounted or bump-feed line types. Spool-mounted lines come in various sizes, such as 0.065", 0.095", and 0.130". Bump-feed lines usually come in 0.080", 0.095", and 0.110" sizes. Ensure you have the correct type and size of line for your Troy-Bilt weed eater before purchasing.

Whatever line type you opt for, make sure it's compatible with your specific Troy-Bilt model. Check your user manual or look up your model online to confirm. Using the wrong type of line can cause damage to your weed eater and decrease its performance.

AD

Loading the New Trimmer Line onto the Spool

First, measure the new trimmer line to ensure the two ends equal the length of the trimmer head's eyelets. If they vary, you can trim the line to the appropriate length with scissors or a line cutter, leaving enough line on both ends for proper operation.

Place the spool on a flat surface or onto a paper towel to catch any excess lubricant. Apply a small amount of general-purpose lubricant, like mineral oil or multipurpose grease, to the groove where the trimmer line will sit. This helps prevent the line from tangling or knotting during operation.

Winding the Line Around the Spool

Starting with the spoolдел, gently wind the trimmer line around the spool. Ensure the line is flat against the spool and keep the first layer as straight as possible. Overlapping or crimping the line can cause tangles and incorrect feeding.

AD

Keep winding the line clockwise, following the arrow on the spool, until around 12-14 feet of line are used. Leave enough line on the outer end (around 6-8 inches) for assembly. You may need to trim any excess line after assembly to prevent it from getting caught in the weed eater's engine or creating hazardous conditions.

Reassembling the Weed Eater Head

Now that your trimmer line is properly wound onto the spool, it's time to reassemble the head. Reverse the process you followed earlier to disassemble the head, ensuring everything is aligned correctly:

  1. Place the spool with the new line onto the bottom portion of the head (the part with the eyelets).
  2. Hold the spool in place and slide the head back onto the weed eater's shaft. Turn it clockwise until it's secure.
  3. Thread the ends of the trimmer line through the eyelets and out the bottom of the head.
  4. Reattach the top half of the head (the part with the nut) and turn it clockwise until it's tightly secured.

Testing the New Trimmer Line

Before you fire up your Troy-Bilt weed eater, perform a quick test to ensure the new line is functioning correctly. Gently pull the ends of the trimmer line to see if they feed smoothly. If the line tangles or doesn't feed, there might be an issue with your assembly.

Once you've verified the new line is feeding correctly, you can plug in your weed eater and give it a quick test run in an open, safe area. The line should spin freely and cut through any weeds or grass it encounters.

Congratulations! You've successfully learned how to string your Troy-Bilt weed eater. Now that you know how to keep your trimmer line in top condition, you can maintain your perfect lawn throughout the year. Happy trimming!

AD