Restart Your Water Heater Pilot Light: Step-by-Step Guide
Have you stepped into a cold shower lately, only to realize that your water heater's pilot light has gone out? Don't let this minor inconvenience dampen your spirits. Restoring the pilot light on your water heater is a simple task that you can undertake safely once you understand the process. Let's guide you through the steps to relight your water heater's pilot light.
Before we dive into the steps, remember that safety comes first. Shut off the power source to your water heater – either the electrical power or the gas supply, depending on the type of your heater – and allow the unit to cool down for about 30 minutes. This ensures that you won't get burned while performing these steps.
Understanding Your Water Heater
Gas and electric water heaters both have pilot lights, but they operate differently. Gas water heaters use a continual flame to heat water, while electric ones heat water through a heating element. Knowing the type of your water heater helps you identify the correct restart procedure. If you're unsure, check your owner's manual or look for the gas or electrical supply pipe connected to your tank.
For this guide, we'll focus on gas water heaters, as they account for over half of water heater installations. However, we'll briefly mention the differences for electric water heaters at the end.
Locating the Pilot Light
Finding the pilot light on your water heater is the first step. It's usually located at the bottom of the tank, near the base, and is protected by a small metal cover. Remove this cover to expose the pilot light area. It might be behind a panel that you'll need to unscrew.
The pilot light itself is a small, continuously burning flame that you should see through a small window or opening, possibly a cylinder shaped part. If the flame is present, you'll see a small, steady blue flame. If it's out, proceed to the next steps. If it's flickering orlarge and yellow, call a professional for service.
Preparing to Relight the Pilot
Before attempting to relight the pilot, make sure your hands are dry, as oil or moisture can create a spark when you turn the knobs. Also, ensure that the area is well-ventilated to prevent any buildup of gas.
Next, turn the control knob on your water heater from "Off" or "Pilot" to "Pilot." After a few seconds, press down and hold the "Pilot" button while keeping the control knob in the "Pilot" position. You should hear a clicking sound as you release a burst of gas.
Relighting the Pilot Light
If everything is working correctly, a click should indicate that the gas is being released, and you should see the pilot light ignite. Keep holding down the "Pilot" button for about 60 seconds to ensure that the flame stays lit and to maintain enough gas pressure in the pilot light area.
Carefully release the "Pilot" button and let go of the control knob. If the pilot light stays lit, you've successfully restarted your water heater. If it goes out, repeat the process. If it still doesn't light, you might have a more significant issue, and it's best to call a professional.
Re-priming Your Water Heater
After relighting the pilot, you may need to re-prime your water heater to get the water flowing again. To do this, turn the control knob to the "On" position and let the water heater run for about 5-10 minutes to restore the water pressure. You might hear some water rushing through the pipes as this happens.
Once you've re-primed your water heater, turn the control knob back to the "Pilot" position. Your water heater should now be working again and providing you with the hot water you need.
Gas vs. Electric Water Heaters: What's the Difference?
If you have an electric water heater, the process to relight the pilot is slightly different. Instead of a continous pilot light, you'll have a heating element that cycles on and off to maintain the water temperature. To relight the element:
1. Turn off the power to your water heater at the circuit breaker panel, not at the water heater itself.
2. Wait for about 30 minutes to allow the water heater to cool down.
3. Locate the thermal cutoff switch on your water heater. This is usually a small box with two wires connected to it.
4. Carefully remove the cover of the thermal cutoff switch and press the reset button. This should relight the heating element.
5. Turn the power back on at the circuit breaker panel and allow your water heater to reheat the water.
That's it! You've successfully relit your water heater's pilot light and ensured that you'll have hot water for your showers, dishwashing, and laundry. Always remember to restart your water heater safely and follow these steps carefully. If you're unsure about any part of the process, don't hesitate to call a professional for assistance.