how to replace pull cord on husqvarna chainsaw

Step-by-Step: Replace Pull Cord on Husqvarna Chainsaw

By William Jones
AD

Mastering the art of DIY maintenance, like replacing a pull cord on your Husqvarna chainsaw, can save you time and money in the long run. This comprehensive guide will walk you through each step, ensuring you get the job done safely and correctly.

Before we dive in, ensure you have the necessary tools: a flathead screwdriver, a new pull cord (matching your chainsaw's make and model), and some gloves for safety. Always remember to disconnect the spark plug when performing maintenance to prevent accidental starting.

Identifying and Removing the Old Pull Cord

First, locate the old pull cord on your Husqvarna chainsaw. It's typically found on the top or side of the machine, connected to the craving mechanism.

AD
How To Adjust A Husqvarna Chainsaw Oiler - Hunker
How To Adjust A Husqvarna Chainsaw Oiler - Hunker
How to Reset the Chain Brake on a Chainsaw | Husqvarna
How to Reset the Chain Brake on a Chainsaw | Husqvarna
How to Replace the Pull Cord on a Stihl KM 56 RC Trimmer
How to Replace the Pull Cord on a Stihl KM 56 RC Trimmer

Using your flathead screwdriver, gently pry out and release the lock tab on the pull cord cover. This should expose the pull start mechanism and the old cord.

Removing the Lock Nut and Old Cord

A lock nut secures the pull cord in place. Unscrew this nut counterclockwise using your screwdriver or a wrench. Once removed, it should free up the old pull cord for easy disposal.

Husqvarna Chain Oiler repair and Easy Clutch Removal Hack
Husqvarna Chain Oiler repair and Easy Clutch Removal Hack
an orange chainsaw sitting on the ground next to a black and white sign that says fix a chainsaw pulling
an orange chainsaw sitting on the ground next to a black and white sign that says fix a chainsaw pulling

Carefully pull out the old cord from the hole, ensuring no leftover pieces or frayed ends remain. A clean surface is crucial for installing the new cord.

Inspecting the Pully and Handguard

Now that the old cord is out, take a moment to inspect the pully and handguard. Make sure there's no excessive wear or damage. If necessary, replace these components before installing the new cord.

AD

Check for any debris or dirt in the splines of the pully. A clean pully will create less friction and make it easier to pull the new cord.

Installing the New Pull Cord

Before installing the new cord, match it to your Husqvarna chainsaw's specifications. The length and type of cord can vary depending on your model. Always ensure you're using genuine Husqvarna parts to maintain your saw's performance and longevity.

Measure and cut the new cord to size. A good rule of thumb is to make the new cord about 1.5 to 2 times the length of the handle. Cut one end of the cord at a 45-degree angle to create a sharp edge that will easily grip the pully.

AD

Threading the New Cord through the Chainsaw

Starting from the inside of the chainsaw, use a thin object, like a needle-nose pliers or a long, thin bolt, to guide the new cord through the hole from which you removed the old cord.

Insert the sharp edge of the cord through the hole first. This will help guide the rest of the cord through smoothly. Continue threading until about 5-6 inches of cord hangs out of the hole.

Securing the New Pull Cord

Slide the lock nut back onto the cord and secure it tightly. Ensure it's perpendicular to the cord to avoid binding or kinks. Use your flathead screwdriver to tighten it clockwise.

AD

Once the nut is secure, reattach the pull cord cover, snap it back into place, and secure it with the lock tab. Test the new pull cord by giving it a few gentle tugs. It should pull smoothly and easily.

Final Checks and Tips

Before you start your chainsaw again, reconnect the spark plug and tighten it securely.

Always dust off and clean your chainsaw after each use. Regular maintenance, including replacing the pull cord, will extend your chainsaw's lifespan and keep it running smoothly.

Congratulations! You've successfully replaced the pull cord on your Husqvarna chainsaw. Embrace your inner handyman and explore other maintenance procedures to keep your tools in top shape. Happy sawing!

AD