How to Remove Whirlpool Washing Machine Drum
Is your Whirlpool washing machine's performance not up to par? Before you consider costly repairs or replacement, why not try a simple troubleshooting step: removing and reattaching the drum for a thorough inspection and cleaning? Many issues, like improper spinning or balancing problems, can be traced back to the drum itself. This guide will walk you through the process of removing and replacing the drum in your Whirlpool washing machine safely and effectively.
Before we start, ensure you have the necessary tools at hand: a socket wrench, a screwdriver, and a flat pry tool. Also, be sure to switch off and unplug the machine from its power source to avoid any electrical hazards during the process. Now, let's dive into the process, step by step.
Preparation and Accessing the Drum
The first step is to prepare your washing machine for access to the drum. Clear the area around the machine, and if possible, place it on a few blocks of wood to tilt it back, providing better access to the bottom.
Using a socket wrench, remove the two lower access panels on the front of the machine. These are typically held in place by bolts and can be unscrewed by turning counterclockwise. Store these panels safely for later reattachment.
Disconnecting the Drive Belt and Pulley
To disconnect the drive belt and pulley from the motor, locate the metal shield at the back of the machine. Using a screwdriver, carefully remove the shield by prying it off from the clips that hold it in place. Once removed, you should see the motor and the drive belt.
Gently ease the belt off the pulley using your fingers. Be careful not to kink or damage the belt during this step. Now, your drum is disconnected from the motor, allowing you to remove it.
Removing the Drum Rear Support Bracket
The drum's rear support bracket secures the drum to the machine's rear wall. Using a screwdriver, remove the screws holding the bracket in place and lift it gently off its position. You may need to wiggle it slightly to free it from its excess material.
Store the bracket safely, keeping its screws and your other tools organized. You'll need them later for reassembly.
Removing the Drum from the Washing Machine
With the belt and rear support bracket removed, you're now ready to extract the drum from the washing machine housing.
Starting from the back, tilt the drum forward gently, allowing it to slide out. As you tilt, keep an eye on the front of the drum to ensure it clears any Support arms or internal components. If the drum is stuck, don't force it. There might be a bearing or seal preventing its extraction.
Inspecting and Cleaning the Drum
Now that your drum is out, inspect it thoroughly for any signs of damage, such as cracks or wear. Check the bearing and the shaft on which it rotates for smooth operation. If there's excessive play or noise, it might be time for replacement.
Wipe down the drum with a clean cloth and mild dish soap to remove any lingering detergent residue or lint that could negatively impact its operation.
Preparing the Drum for Reattachment
Before you reattach the drum, make sure it's completely dry and free of any debris. Carefully align the drum's shaft with the bearing at the back of the machine and the opening at the front.
Tilt the drum backward, gently pushing it into the machine until the shaft is firmly seated in the bearing. The edge of the drum should nestle into the moon-shaped notch designed to hold it in place.
Reassembling the Washing Machine
Once the drum is securely positioned, it's time to start reversing the disassembly process.
Reattaching the Rear Support Bracket
Replace the rear support bracket, ensuring it's properly aligned with the drum and the machine's rear wall. Secure it using the screws you previously removed.
Tighten the screws firmly but be careful not to overtighten, as this can strip the screw holes or damage the bracket.
Reinstalling the Drive Belt and Pulley
Reattach the drive belt to the motor pulley, ensuring the belt is seated correctly and tensioned appropriately. The belt should fit snugly around the pulley, with no slack.
Reattach the metal shield over the motor and belt, securing it using the clips you removed earlier.
Final Touches and Testing
Replace the two lower access panels you removed earlier, securing them with the bolts you unscrewed. Tighten the bolts using a socket wrench, ensuring they're snug but not overtightened.
Once everything is back in place, plug your washing machine back into its power source and switch it on. Conduct a test cycle to ensure your Whirlpool washing machine is operating correctly and that the drum is spinning smoothly.
If you performed a thorough cleaning and the drum operates as expected, you've successfully removed and replaced the drum in your Whirlpool washing machine. However, if you encounter difficulties or notice any irregularities during the test cycle, it might be best to consult a professional repair technician.
**Remember, always prioritize safety. If a task appears daunting or risky, don't hesitate to call a professional. Keep your hands, face, and hair clear of moving parts, and never put metal objects into a running washing machine.**
Your Whirlpool washing machine should now be performing at its best, ready to tackle your laundry piles with renewed efficiency. Enjoy your clean clothes, and happy washing!