how to put string on a husqvarna weed eater

How to Attach a String Trimmer to Your Husqvarna Weed Eater

By Andrew Lewis
AD

So, you've invested in a Husqvarna weed eater, a powerful tool for taming your lawn edges and hard-to-reach spots. But now, you're faced with the challenge of how to put a new string on it. Fret not, as we're here to guide you through this process with step-by-step instructions. Let's dive into the world of weed eater maintenance and help you get your tool back in working order.

Before we begin, ensure you have the right string for your Husqvarna model. Consult your user manual or Husqvarna's website for the recommended string type. We'll be using a generic walkthrough, but specific models may have slight variations in the process.

Preparing Your Husqvarna Weed Eater

Begin by ensuring your weed eater is turned off and has cooled down if it was recently used. Unplug the tool from the power source for safety. Next, take apart the trimmer head. This is typically done by holding the trimmer head housing and turning the spool counterclockwise until it unscrews and releases.

AD
HOW TO STRING DOUBLE-HEADED WEED EATERS #shorts
HOW TO STRING DOUBLE-HEADED WEED EATERS #shorts
How to Change the Line | Weed Eater String | Replace Weed Wacker [2021]
How to Change the Line | Weed Eater String | Replace Weed Wacker [2021]
10 Best Gas String Trimmers Reviewed (Summer 2026)
10 Best Gas String Trimmers Reviewed (Summer 2026)

You might need to use a little force, but be careful not to damage the spool. With the spool removed, you should now see the coil of line wrapped inside the trimmer head. This is where you'll add your new string.

Measuring the New String

Before installing the new string, measure it to ensure you're using the correct length. Most Husqvarna weed eaters use a 50-foot string, but it's always best to check your model's specifications. Cut the string to the appropriate length, leaving some extra for winding and trimming.

Easy Feed Nylon Head
Easy Feed Nylon Head

If your string is not pre-cut, you can cut it using a sharp pair of scissors or a utility knife. Ensure the ends are even and smooth to prevent fraying and easy feeding into the trimmer head.

Winding the New String

Now that you have your new string measured and cut, it's time to wind it onto the trimmer head spool. Start by inserting one end of the string through the hole in the top of the trimmer spool. Pull the string through until you have around 6 to 10 inches of line sticking out on the other side.

AD

The purpose of this initial extra line is to prevent the string from slipping back into the spool when you insert it back into the weed eater. After pulling your line through, you're ready to start winding.

Winding the String Correctly

Correct winding is crucial for optimal performance and safety. Most Husqvarna trimmers use a 'C' or 'CCW' winding pattern. This means you'll wind the string counterclockwise, with each new layer of string laid on top of the previous one in the opposite direction.

To do this, hold the line tail and begin winding the string around the spool, ensuring you're going in the right direction. Maintain tension on the string as you wind to avoid creating any slack or kinks. You should end up with the line wrapped on the spool in an even layer with the tail sticking out.

AD

Securing the New String

Once you've wound the string onto the spool, you'll need to secure it to prevent the line from unraveling when you insert it back into the weed eater. To do this, you can either wrap the line tail around the outside of the spool a few times or insert it into a small hole or slot on the spool designed for this purpose.

If your Husqvarna trimmer does not have this hole, you can simply tuck the line tail under the outer layer of the string. This should be enough to keep the line in place during operation.

Re-assembling Your Weed Eater

With the new string secured, the last step is to insert the spool back into the trimmer head and then attach the trimmer head back onto the weed eater. Twist the spool clockwise to wind the excess line back onto the spool until it's taut, then hold the spool and turn the trimmer head housing counterclockwise until it clicks into place.

AD

Test your weed eater by pulling the trigger and letting out a suitable amount of line. If everything is set up correctly, you should see the string unwind smoothly, ready for use.

And there you have it! With your new string securely installed, you're ready to tackle those overgrown edges and hard-to-reach spots once again. Regular maintenance like this helps keep your Husqvarna weed eater in top working condition, ensuring a well-manicured lawn and years of reliable service. Happy trimming!

AD