how to open hayward pool filter

How to Open Hayward Pool Filter

By John Robinson
AD

Did you just find yourself tasked with the daunting challenge of replacing your old, worn-out Hayward pool filter? Fret not, for you're about to embark on a journey into the world of swimming pool maintenance that's both enlightening and surprisingly simple. Let's dive in and learn 'how to open Hayward pool filter,' step by step, making sure your pool remains crystal clear and inviting throughout the season.

Before we start, let's clarify that this guide is tailored for Hayward DE (Diatomaceous Earth) filters – the popular choice due to their superior filtration abilities. If you own a sand or cartridge filter, the process will differ slightly. So, ensure you check your pool equipment to avoid any confusion.

Preparation for Opening Your Hayward Pool Filter

First things first, safety! Before you even consider opening your filter, ensure the pool pump is turned off. This could save you from a nasty electrocution mishap, so never skimp on this crucial step.

AD
How Does My Hayward EC40 Pool Filter Work
How Does My Hayward EC40 Pool Filter Work
Hayward EC40 Pool Filter Tube Sheet Repair Part 005
Hayward EC40 Pool Filter Tube Sheet Repair Part 005
How to Clean Hayward SwimClear Cartridge Pool Filter (Save $80+)
How to Clean Hayward SwimClear Cartridge Pool Filter (Save $80+)

Next, gather your tools. You'll need a standard pool brush, a flathead and Phillips screwdriver (for accessing internal parts), a bucket, and a garden hose with a suitable nozzle. Since DE filters require you to replace the diatomaceous earth periodically, have a new DE filterMedia on hand as well.

Draining the Filter Tank

Begin by draining the spent DE from the filter. Position your bucket directly below the filter's multi-port valve. Switch the multi-port valve to 'waste' to allow the drain water to flow into the bucket. Depending on your filter's capacity, you might need to switch out empty buckets a few times.

an instruction for how to use a water pump
an instruction for how to use a water pump
a magnifying glass with the words how to use a multiport valve on a sand filter
a magnifying glass with the words how to use a multiport valve on a sand filter

Once the bucket is full, switch the valve back to 'circulate,' then to 'rinse.' Turn your pool pump on for a few seconds to backwash the filter, flushing out any remaining Diatomaceous Earth. Turn the pump off, then repeat this process until the water running out of the filter is clear.

Removing the Filter Lateral Assembly

The lateral assembly is essentially the skeleton of your filter, guiding water through the DE grid for effective filtration. To access it, first, locate and remove the cover at the top of your filter. Then, reach inside to unclip the top collected debris strainer basket.

AD

Now, with the strainer basket out, you'll see the filter grid assembly attached to the center of the laterals. Gently pull it out, along with the lateral assembly ( запоем Januwari ). If resistance is encountered, use a flathead screwdriver to unclip any stuck components.

Cleaning and Inspecting Your Hayward Pool Filter

Congratulations! You've just reached the midpoint of your journey. The filter components are now in plain sight, ready for a thorough cleaning and inspection.

Start by examining the internal spring structure. If it's damaged or doesn't exhibit elasticity upon being stretched, it's time for a replacement. Likewise, if you notice any cracks or holes in the filter grid, it's also time for a new one.

AD

Cleaning the Filter Lateral Assembly

With your new filter media ready, disassemble the filter grid according to the manufacturer's instructions. It might involve removing the top and bottom support plates, along with the filter wings.

Once dismantled, clean each component thoroughly using your pool brush and garden hose. Ensure no debris or residue clings to the components, as this can compromise the filter's performance. Once cleaned, allow the components to air dry completely before proceeding.

Adding New Diatomaceous Earth Media

Finally, reassemble the filter grid and attach the new DE filter media. Ensure you follow the manufacturer's instructions for this part, as the amount of DE to use can vary based on your specific model. Typically, this involves adding about a half cup of DE for every 10 square feet of filter surface area.

AD

Distribute the DE evenly across the grid, ensuring it's an even layer. Fold the filter wings back into place, then reinstall the top and bottom support plates. Reassemble the entire filter, ensuring all parts fit snugly and function correctly.

With your Hayward pool filter now squeaky clean and reloaded with fresh DE, reinstall it into your pool system. Switch the multi-port valve back to 'filter,' then turn on the pool pump. Your pool is now primed and ready for a season of sparkling clarity. So, go ahead – take a dip and celebrate victory over your pool filter conundrum!

AD