how to change sand in hayward pool filter

Step-by-Step Guide: How to Change Sand in Hayward Pool Filter

By Andrew Johnson
AD

Keeping your Hayward pool filter's sand clean and fresh is vital for optimal performance and maintaining crystal-clear water. Over time, sand can become contaminated with debris, chemicals, and bacteria, leading to reduced filtering efficiency. Thus, it's essential to replace the sand in your Hayward pool filter periodically. Here's a comprehensive guide on how to change sand in your Hayward pool filter, ensuring your pool stays sparkling and inviting.

Before we dive into the process, ensure you have the following materials at hand: a bucket, a garden hose with a nozzle, a replacement 20- to 30-pound bag of Hayward's #20 sand, and about an hour of your time. Also, make sure your pool pump is off and the pressure gauge on the filter reads 0 PSI.

Preparation and Draining

Begin by turning off your pool pump and timer. Allow the water in the filter to circulate for a few minutes to ensure all sand is distributed throughout the tank. Then, switch off the pump and wait for a few hours to let the sand settle at the bottom of the filter.

AD
How to Change Pool Filter Sand
How to Change Pool Filter Sand
two people standing next to each other near a large object with writing on it that says, every step you need is right here
two people standing next to each other near a large object with writing on it that says, every step you need is right here
How to Change Pool Filter Sand
How to Change Pool Filter Sand

Next, use a key or an adjustable wrench to loosen and remove the drain plug at the bottom of your Hayward filter. Allow the sand to drain thoroughly. You might want to wear gloves during this process to protect your hands from the fine grains. Keep an eye on the amount of sand being released to avoid plugging the drain line.

Removing the Internal Parts

Once most of the sand has drained, close the drain valve. Go to the top of the Hayward filter and remove the collection jar. Then, disconnect the pump and remove the entire internal assembly (standpipe, laterals, and manifold) from the filter tank. Gently scrape off any remaining sand with a putty knife or a razor blade.

How to Clean a Pool Filter (Sand, Cartridge, D.E.)
How to Clean a Pool Filter (Sand, Cartridge, D.E.)
two men standing next to each other near a water tank with a pump on it
two men standing next to each other near a water tank with a pump on it

Be cautious while handling the internal parts, as they can break easily, leading to expensive repairs. If you're using a Perflex tank, lower the diffuser assembly before removing the laterals. Ensure that all O-rings are in good condition and replace them if necessary before re-assembling the filter.

Cleaning the Filter Tank

Rinse the inside of the filter tank with clean water from a garden hose. Aim the waterjet into the tank from various angles to loosen any remaining sand or debris. Be careful not toExtended Your newly cleaned filter tank. Ensure it's completely dry before adding new sand to prevent biological growth.

AD

Before introducing the new sand, make sure the bottom drain and standpipe are clean and free from any obstructions. Also, lubricate the O-rings with a small amount of pool filter oil or silicone grease to ensure a proper seal when you re-assemble the filter.

Adding New Sand to the Filter

Start adding about half of the replacement Hayward #20 sand bag into the filter tank. Pour it slowly and evenly across the base of the tank to ensure an even layer. Avoid heaping the sand in one area, as this can lead to uneven distribution and affects the filter's performance.

After adding half of the bag, moisten the sand lightly with your garden hose to prevent dust from flying around when you start the filter. Then, add the remaining sand, again pouring it evenly across the base of the tank. Ensure the sand level does not exceed the top of the laterals to avoid reducing the filter's efficiency.

AD

Re-assembling the Filter

Carefully place the entire internal assembly (standpipe, laterals, and manifold) back into the filter tank, ensuring the laterals are appropriately aligned with the sand surface. Slowly lower the diffuser assembly (for Perflex tanks) or the entire internal part (for Defender tanks) back into the tank.

Refit the pump and collection jar, tightening them securely. Reinstall the drain plug at the bottom of the filter, ensuring it's properly sealed. If you have a multi-port valve, set it to the "Recirculate" position and turn your pool pump back on.

Re-priming the Pump and Inspection

Unscrew the air bleeder valve on top of the filter and allow air to escape until water drips out. Tighten the valve and slowly turn the multi-port valve to the "Filter" position. Monitor the pressure gauge to ensure it reads around 10 PSI, indicating that the filter is primed and functioning correctly.

AD

After running the filter for about 20 minutes, check the pressure gauge again. If the pressure has climbed more than 5 PSI, backwash the filter according to your Hayward pool filter's instructions. Once done,re-start the filter and continue monitoring the pressure.

Congratulations! You've successfully learned how to change sand in your Hayward pool filter. By following these steps, you'll enjoy crystal-clear water, enhanced filtering efficiency, and a longer-lasting Hayward pool filter. Regularly check your filter's pressure and clean or replace the sand as needed to maintain its optimal performance.

AD