how to install everydrop water filter 1

How to Install EveryDrop Filter 1

By Brian Robinson
AD

Are you looking to improve the water quality in your home? Installing an Everydrop water filter, such as the Everydrop Water Filter 1 (WF1), can significantly enhance your water's taste and remove contaminants. This guide will walk you through the process of installing this filter in your refrigerator, ensuring you enjoy fresh, clean water in no time.

The Everydrop WF1 is designed to be a breeze to install. It eliminates the need for excessive plumbing or complicated tools, making it a perfect DIY project. Before you start, ensure you have the following items: your new Everydrop water filter, a Philips screwdriver, and about 30 minutes to spare. Let's dive into the step-by-step process.

Removing the Old Filter

Before installing the new filter, you need to remove the old one. Start by turning off the water supply valve located under your refrigerator. Then, turn off the ice maker and water dispenser.

AD
How to Install a Kitchen Instant Hot Water Dispenser, Faucet and Water Filter - Part 2 - HandyManHowTo
How to Install a Kitchen Instant Hot Water Dispenser, Faucet and Water Filter - Part 2 - HandyManHowTo
How to Install an Under Sink Water Filter System
How to Install an Under Sink Water Filter System
How To Change Whole House Sediment Water Filter St
How To Change Whole House Sediment Water Filter St

Next, locate the filter housing, usually found at the back of the refrigerator. Twist the filter cap clockwise to loosen it, then unscrew it completely. Once done, pull out the old filter gently. Remember to recycle it according to your local recycling guidelines.

Preparing the New Filter

Before installing the new filter, you need to prepared it. First, remove the protective cap and wrap it in a plastic bag or towel to keep it clean. Next, place the filter in a large container or basin and fill it with water. Let it soak for 15 minutes to allow the filter media to expand.

How to Install an Instant Hot Water Dispenser, Faucet and Water Filter - Part 3 - HandyManHowTo
How to Install an Instant Hot Water Dispenser, Faucet and Water Filter - Part 3 - HandyManHowTo
a person is holding an electric toothbrush in front of a water filter
a person is holding an electric toothbrush in front of a water filter

After soaking, discard the water and rinse the filter thoroughly. This step helps to remove any loosely adhered carbon particles that could otherwise end up in your water.

Installing the New Filter

Now that the filter is prepared, it's time to install it. Start by replacing the protective cap back onto the filter. Ensure it's properly secured to prevent leaks.

AD

Next, insert the filter into the filter housing. Align the arrows on the filter with the ones on the housing to ensure it's properly oriented. Once aligned, twist the filter clockwise until it's fully seated in the housing. Make sure it's secured tightly to prevent leaks, but avoid overtightening.

Reassembling and Flushing the System

After installing the new filter, it's time to reassemble and flush the system. Start by replacing the filter cap and twisting it counterclockwise until it's securely in place.

Then, turn on the water supply valve and let the water run through the filter for about 5 minutes. This step flushes the system and ensures that the water dispenser and ice maker are filled with fresh, filtered water.

AD

Activating the Filter Light

Most refrigerators with water filters have a light that indicates when it's time to replace the filter. To activate this light, first, remove the grill at the bottom of the refrigerator that covers the water tank. Then, press and hold the filter reset button for about 3 seconds.

Once the light comes on, wait for about 2-3 minutes, then press the button again. The light will blink twice to indicate that the filter has been reset. Replace the grill, and you're done!

Monitoring and Replacing the Filter

Congratulations! You've successfully installed your new Everydrop water filter. To ensure optimal performance, monitor the filter light. Replace the filter when the light turns red, usually after about 6 months or 200 gallons, whichever comes first.

AD

Regularly replacing the filter helps maintain the water's taste and quality and ensures your refrigerator's components remain clean and functional. Some refrigerators also have an app or digital display that can remind you when it's time to change the filter.

Enjoying fresh, clean water is one of life's simple pleasures. With a little effort and the right tools, installing the Everydrop Water Filter 1 ensures you have access to that pleasure, any time you want. Cheers to your newfiltered water experience!

AD