how to install a gas water heater youtube

Step-by-Step: Install a Gas Water Heater - YouTube Guide

By Emily Lopez
AD

Planning to install a gas water heater at home? You've come to the right place. We're here to guide you through the process with a comprehensive, step-by-step guide. Let's dive right in, ensuring your safety and a job well done.

Before we begin, remember that working with gas appliances requires caution. If you're unsure about any steps, always consult a professional.

Preparation and Safety Checks

Before you start, ensure you have all the necessary tools and materials:

AD
How To Install A Gas Water Heater
How To Install A Gas Water Heater
How to Install a Tankless Gas Water Heater - The Home Depot
How to Install a Tankless Gas Water Heater - The Home Depot
How To Turn On or Reset a Gas Water Heater
How To Turn On or Reset a Gas Water Heater
  • Gas water heater
  • Teflon tape
  • Adjustable wrench
  • Pipe wrench
  • Screwdriver
  • Copper water supply lines (if not included with the heater)
  • Venting materials (depending on your vent type)

Gas Valve

First, turn off the gas valve at the inlet pipe and the main gas supply. Open a hot water faucet to relieve any pressure in the lines.

Then, install the new gas valve on the water heater, ensuring it's securely attached and leaked-free.

How to Install a Tankless Water Heater
How to Install a Tankless Water Heater
A.O. Smith University Gas Water Heater Installation
A.O. Smith University Gas Water Heater Installation

Venting

Venting is crucial for safe operation. If your heater is powered by natural gas, it requires proper ventilation. Follow the manufacturer's instructions for your specific vent type.

For direct vent heaters, ensure the vent pipe is securely attached to the heater and that there are no gaps or leaks. For power-vented heaters, connect the vent pipe to the exchanger consistently with the manufacturer's guidance.

AD

Water Lines and Drain Valve

Now, let's connect the water supply lines. Typically, you'll find the input and output lines at the top of the water heater.

Use Teflon tape to ensure a tight seal on the threads before connecting the copper supply lines. Secure them using a pipe wrench for a leak-free connection.

Drain Valve

Locate the drain valve, usually at the bottom of the tank. Ensure it's open for any remaining water and debris to drain out during the initial filling.

AD

Once drained, close the valve and connect a garden hose (not included with most heaters) for easier cleanup.

Temperature and Pressure Relief Valve

Install the temperature and pressure relief valve (TPR) according to the manufacturer's instructions. This crucial component prevents excessive temperature or pressure buildup in the tank.

Ensure it's connected to a dedicated pipe leading outside the house, preferably within 6 feet of the heater. This will safely vent any excess steam or water.

AD

Installing the Gas Water Heater

With all the connections in place, it's time to mount the water heater. Remember to secure it to the nearby wall or framing using the provided hardware.

Ensure the heater is level and the combustion air intake remains unobstructed. For direct-vented heaters, ensure the intake vent is clear and not blocked by a wall or cabinet.

Gas Line Connection

Connect the gas line to the gas valve inlet on the water heater. Again, use Teflon tape to ensure a tight seal. Secure it using a wrench, but be careful not to overtighten.

Once connected, slow open the main gas supply valve. You should hear gas flowing through the pilot light. If there's no flow, check for leaks or obstructions.

Lighting the Pilot

Follow the manufacturer's instructions to light the pilot. Typically, you'll need to press and hold the igniter button while another button is pressed to introduce gas.

Once the pilot is lit, you can release the buttons. If the pilot light goes out, there may be a draft or air pocket. Wait a few minutes and try again.

Testing the Installation

Now that everything is connected, it's time to test your newly installed gas water heater.

Open a hot water faucet to relieve any air pressure from the supply lines. Then, switch the heater to the "On" position and listen for the click of the gas igniter.

Water Heating

Without opening any more faucets, allow the water in the tank to heat up. This can take up to an hour depending on your heater's size and capacity.

After about 30 minutes, turn on a hot water faucet and let the water run for a few minutes to ensure it's adequately heated. Be cautious; the water may come out very hot initially.

Final Checks

Verify that the water heater is operating correctly and there are no leaks. Inspect all connections for signs of water or gas leaks.

Lastly, monitor the temperature and pressure relief valve periodically. If it's functioning correctly, you should occasionally hear it release small amounts of water.

Congratulations! You've successfully installed your gas water heater. Regular maintenance will keep it running smoothly. Don't hesitate to call a professional if you encounter any issues during or after the installation process.

AD