troy bilt tb32ec how to change string

Troy-Bilt TB32EC: String Trimmer Guide - How to Change the Line

By Andrew Hernandez
AD

Need to replace the string on your Troy-Bilt TB32 EC hedge trimmer? It's a simple process, and with the right steps, you can have your hedge trimmer back in action in no time. Let's dive into a detail-by-step guide on how to change the string on your Troy-Bilt TB32 EC.

Before we start, ensure your hedge trimmer is unplugged and cool to the touch. Safety first, right? Now, let's get started with the first main topic: gathering your materials and preparing the trimmer.

Gathering Materials and Preparing the Trimmer

First, you'll need to gather a few materials: a new spool of string (ensure it's compatible with your TB32 EC), a flathead screwdriver, and a pair of work gloves for safety. Next, prepare your trimmer by locating the string release lever on the side of the trimmer's head. This lever allows you to rewind the string for replacement.

AD
Super Easy String Line Trick | #hardscaping #pavers #concrete
Super Easy String Line Trick | #hardscaping #pavers #concrete
How I Knew The String Would Cut and Won $100! [Barber Cut Lite Hacks]
How I Knew The String Would Cut and Won $100! [Barber Cut Lite Hacks]
Troy 💚
Troy 💚

Now, let's move on to the sub-topics under this main topic. We'll start with measuring and preparing the new string.

Measuring and Preparing the New String

Before you start, measure the length of the old string. This will give you a good idea of how much new string you'll need. Typically, the TB32 EC uses a 0.063-inch blade and a 0.080-inch trimmer line. Cut your new string to the same length as the old one, usually around 20 feet. It's better to have a bit too much than not enough. You can always trim it later.

Mtd 946-1100 Throttle Cable Troy-Bilt Horse GTX Revolution LT 804h 804p 818p, White
Mtd 946-1100 Throttle Cable Troy-Bilt Horse GTX Revolution LT 804h 804p 818p, White
Bow Tuning Tips / String Splitting the Right Way
Bow Tuning Tips / String Splitting the Right Way

Once you've cut the string, separate about 12 inches of string from the spool. You'll use this to feed through the trimmer's head. Keep the rest of the string on the spool for easy management.

Replacing the String

Now that we're ready, let's move on to replacing the old string with the new one. First, we'll show you how to remove the old string, then we'll guide you through feeding and rewinding the new string.

AD

To remove the old string, follow these steps:

  • Grasp the end of the old string with one hand and release the string release lever on the side of the trimmer with the other.
  • Pull the old string out through one of the eyelets (make sure it's the correct one for your trimmer).
  • continuation>

With the old string removed, it's time to feed and rewind the new string. This process involves two sub-topics: feeding the string and rewinding the line.

Feeding the String

Begin by inserting the 12-inch piece of the new string you separated earlier into the feed opening on the side of the trimmer's head. You should see an arrow marking the direction you need to feed the string. Use your flathead screwdriver to help guide the string through, if needed.

AD

}

Rewinding the Line

With the string fed through, it's time to rewind it. Engage the string release lever again and slowly pull the string out through the other eyelet until it's completely wound around the spool. Make sure the string doesn't tangle or overlap as you wind it.

Once the string is fully rewound, disengage the lever. Your trimmer is now ready to go. As a final step, cut the excess string from both sides of the trimmer, leaving about 4 to 6 inches of string on each side.

AD

And there you have it! You've successfully changed the string on your Troy-Bilt TB32 EC hedge trimmer. Don't forget to test your trimmer before you start your next project. Happy trimming!

AD