Husqvarna Weed Eater String: Steps to Replace
Taming your overgrown weeds can be a daunting task, but with the right tools and a bit of knowledge, it becomes manageable. One of these tools is the weed eater, or string trimmer, a versatile device beloved by gardeners worldwide. A brand that stands out in this market is Husqvarna, renowned for their durable and high-performing devices. But like all tools, they require maintenance to ensure optimal performance. One of the most common tasks is winding new weed eater string. Let's delve into a step-by-step guide on how to do this for your Husqvarna weed eater.
Before we begin, ensure your weed eater is suitable for your task. Husqvarna offers a range of trimmers with varying power, from their lightweight 14" Loop Handle Trimmer to their heavy-duty 21" Burr-Pmiral Trimmer. Choose a machine that matches your yard's size and your cutting needs.
Understanding Your Husqvarna Weed Eater's Spool
The spool is the heart of your weed eater, holding the feed spool (trimmer line) that slices through weeds. Understanding its parts is key to reloading it correctly. The most common Husqvarna trimmers use either a Tilt-Trim or a DuoCut system. The Tilt-Trim system allows you to trim hard-to-reach areas, while the DuoCut system caters to both straight and curl-type trimming heads.
To identify your spool type, consult your weed eater's manual or look for the distinctive Tilt-Trim or DuoCut logos on the spool cover. Once you've identified it, you're ready to proceed with the winding process.
Preparing the New String
Start by determining the length of new string needed. For most Husqvarna trimmers, you'll need around 50 feet of .095" or .105" diameter trimmer line. Cut this into two lengths, each about half the total amount. This ensures you've enough string on each side for even feeding.
Before loading, check your spool's direction of rotation. It's usually indicated on the spool cover. Your new string should run in the same direction.
Loading the String onto the Spool
Here's where the process differs slightly between the Tilt-Trim and DuoCut systems:
For Tilt-Trim systems:- Remove the spool cover. The spool might 'pop' out, or you may need to unscrew it.
- Insert one end of your cut string into the hole in the spool's center (or the underside, if it's a top-fill spool).
- Wind the string around the spool in the correct direction, keeping it neat and evenly spaced.
- Once you've used about 6-8 feet of string, insert the other end of the string into the hole on the spool's outer edge (arboreal feed spool).
- Continue winding, using up all the string. Ensure it's wound tightly against the spool.
- Finally, insert the string ends back into the holes on the spool's outer edge, leaving about 6-10 inches of string sticking out for each side.
Follow the initial four steps for the Tilt-Trim. After that:
- Wind the string around the inner spool (the one with the bump head) first, then onto the outer spool, ensuring it's wound in the correct direction.
- When you wind the string onto the outer spool, leave some slack to allow for the trimming head's action.
Reassembling Your Husqvarna Weed Eater
Now that you've correctly loaded your string, it's time to reassemble your weed eater:
Reinstalling the Spool
Insert the spool back into the trimmer's housing. It should only go in one way, so don't force it. Reattach the spool cover. If it's not clicking into place, try a different orientation.
Adjusting the String Length
With the spool back in place, pull out the excess string from both sides. You want about 6-10 inches of line extending from each side. If your string's too long, you can cut it. If it's too short, you'll need to go back to your spool and adjust accordingly.
Your Husqvarna weed eater should now be ready to tackle those overgrown weeds. Regular string maintenance is key to keeping your trimmer running smoothly. Don't forget to replace your string as нуж as it wears out. Happy gardening!