how to test gm ignition coil with multimeter

Simple Test: How to Check GM Ignition Coil with a Multimeter

By Richard Lewis
AD

If your General Motors (GM) vehicle is experiencing starting difficulties or poor performance, a faulty ignition coil could be the culprit. Ignition coils play a crucial role in converting the vehicle's battery voltage into a higher voltage needed to create the spark that ignites the fuel-air mixture in the engine. To pinpoint a faulty ignition coil, you can test it using a multimeter. This article guides you through the process, helping you diagnose the ignition coil and resolve any potential vehicle issues.

Before we proceed, ensure you have a multimeter and understand its operation. If you're new to multimeters, familiarize yourself with the different settings and features. Also, Remember to always disconnect the negative battery cable before performing any diagnostic tests to prevent electrical shorts and ensure your safety.

Understanding Ignition Coils

Ignition coils are essentially transformers that step up the battery's 12-volt supply to as high as 20,000 to 30,000 volts, depending on the vehicle. They are made up of two main components: the primary winding (low voltage) and the secondary winding (high voltage). The multimeter test involves examining these components to determine if the coil is functioning correctly.

AD
How to Test an Ignition Coil with a Multimeter (7-Step Guide)
How to Test an Ignition Coil with a Multimeter (7-Step Guide)
How to Test Ignition Coil with Multimeter
How to Test Ignition Coil with Multimeter
How To Test And Troubleshoot Ignition Coils - Hunker
How To Test And Troubleshoot Ignition Coils - Hunker

GM vehicles typically use one ignition coil per cylinder. Therefore, you'll need to test each coil separately to identify any faulty components. Most modern GM vehicles use coil-on-plug (COP) systems, which means one coil is dedicated to each spark plug. Locate the ignition coils based on your vehicle's year, make, and model, and always consult your vehicle's repair manual for specific instructions.

Preparation before Testing the Ignition Coil

Before starting the testing process, gather the necessary tools and gather information about your vehicle. You'll need:

How to check ignition coil with multimeter
How to check ignition coil with multimeter
How to Test a Coil Pack with a Multimeter (Step-by-Step Guide)
How to Test a Coil Pack with a Multimeter (Step-by-Step Guide)
  • A digital multimeter with the capability to measure resistance (ohms) and voltage (DCV).
  • A repair manual specific to your GM vehicle for accurate wire and connection locations.
  • Ratchet sets, sockets, and other tools needed to access and disconnect components.
  • Safety glasses and gloves to protect yourself during the process.

After gathering your tools, park your vehicle on a level surface and allow the engine to cool down to prevent burns. Finally, disconnect the negative battery cable to avoid electrical shorts during testing.

Testing Ignition Coil Resistance

The primary and secondary windings of the ignition coil should have specific resistance values. Measuring these resistances helps identify any shorted or open circuits within the coil. Follow these steps to test the ignition coil's resistance:

AD
  1. Disconnect the ignition coil's electrical connector(s) and set your multimeter to measure resistance (ohms).
  2. Measure the resistance across the connector's terminals or coil's wires, depending on the connection type. Compare your results with the specified values in your repair manual.
  3. electrolytic capacitors within the ignition coil or its harness. If present, measure the resistance across their terminals; it should be infinite (open circuit) for healthy capacitors.

Here's an example of resistance values for GM ignition coils:

Coil Type Primary Winding Resistance (ohms) Secondary Winding Resistance (ohms)
GM Ignition Coil (Most Applications) 3.0 - 7.0 20,000 - 30,000

If the measured resistance values fall outside the specified ranges, replace the ignition coil as it is likely faulty.

Testing Ignition Coil Induction Voltage

After checking the coil's resistance, test the induction voltage to ensure that the coil is producing the required spark. To test the induction voltage, you'll need to temporarily connect the coil to the vehicle's battery and measure the output voltage at the spark plug.

AD

To test the induction voltage, follow these steps:

  1. Reconnect the negative battery cable and ground the multimeter's black lead to a suitable location, such as the engine block or a clean metal part of the vehicle.
  2. Set your multimeter to measure DCV (direct current voltage).
  3. Disconnect the ignition coil's electrical connector and any additional wiring connected to the coil.
  4. Connect the multimeter's red probe to one of the coil's remaining terminals, and temporarily connect the coil's other terminal directly to the positive battery terminal using a jumper wire.
  5. Have a helper crank the engine with the ignition system off, and read the voltage on your multimeter. Compare the recorded voltage with your repair manual's specifications. If the voltage is within the specified range (typically around 250 to 400 volts), the ignition coil is likely functioning correctly.

If the measured voltage is low or unobtainable, and the resistance test suggests a healthy coil, the issue might lie within the vehicle's ignition system or the power delivery to the coil. Inspect the components related to the ignition system, such as the pick-up coil, crankshaft position sensor, ignition control module, and any wiring or connectors that could be faulty.

Testing Ignition Coil Wiring and Connectors

After testing the coil's internal resistance and induction voltage, check the coil's wiring and connectors for any damage, breaks, or corrosion. Console the visually inspect the wiring for any broken strands, frays, or damage. If the wire insulation is broken or worn, replace the wire or the entire harness if necessary.

AD

Next, inspect the electrical connectors for any damaged terminals, corrosion, or signs of overheating. Clean the connectors using a suitable cleaning agent if required, and ensure that they are securely connected with no visible damage.

Finally, verify that all the electrical connections are clean, tight, and corrosion-free. If any connectors or wires appear damaged, replace them to ensure the proper functioning of the ignition system. Keep in mind that a poorly sourced voltage or signal can cause a seemingly good ignition coil to fail.

After conducting a thorough diagnosis, replace any faulty components and reassemble your vehicle. If you've followed the steps outlined in this article and replaced any defective components, your vehicle's starting and performance issues should be resolved. Regularly inspect and maintain your ignition system to prevent any future issues. Happy wrenching!

AD