how to test 2 stroke ignition coil

How to Test a 2-Stroke Ignition Coil: A Step-by-Step Guide

By Jessica Johnson
AD

Are you experiencing misfires, power loss, or starting troubles with your two-stroke engine? The ignition coil could be the culprit. Testing your 2-stroke ignition coil is crucial to ensure your engine gets the right spark at the right time. This detailed guide will walk you through the process, helping you diagnose and potentially fix the issue at home.

Before we dive into the testing process, it's essential to understand that ignition coils are designed to step up the battery's 12 volts to as much as 20,000 to 30,000 volts to create an effective spark for your engine. When they fail, it's usually due to normal wear and tear, or a blown fuse, and they need to be tested or replaced.

Preparation and Safety

Before performing any testing, ensure your engine is cool and not running. Also, disconnect the negative (-) battery cable to prevent any short circuits. Remember to follow proper safety protocols when working with electrical components.

AD
How To Test And Troubleshoot Ignition Coils - Hunker
How To Test And Troubleshoot Ignition Coils - Hunker
Ignition Coil Operation and Diagnostic Testing
Ignition Coil Operation and Diagnostic Testing
an image of a car's fuel pump and its hose connected to the tank
an image of a car's fuel pump and its hose connected to the tank

You'll need a multimeter to test your ignition coil. A multimeter is a diagnostic tool that measures voltage, resistance, and current. If you don't have one, they are relatively inexpensive and can be found at most auto parts stores.

Testing the Primary Winding

The primary winding of the ignition coil is responsible for building the current that creates the high voltage spark in the secondary winding. To test it, you'll need to check the resistance and the continuity between the terminals marked for the battery (+) and (-) or 'P' and 'B'.

spark tester with instructions on how to use the spark tester and what it uses
spark tester with instructions on how to use the spark tester and what it uses
How to Test Ignition Coils
How to Test Ignition Coils

Using your multimeter, set it to the ohms (Ω) setting. Touch one probe to each of the primary winding terminals. You should read a resistance of between 0.5 to 2 ohms. If the reading is infinity (shown as '∞' or 'OL'), the coil is likely shorted or open, indicating a problem.

Testing the Secondary Winding

The secondary winding is where the high voltage that creates the spark is generated. To test it, check the resistance and continuity between the 'T' and 'C' or 'H' terminals, which connect to the spark plug.

AD

Again, using your multimeter on the ohms (Ω) setting, you should read a resistance between 6,000 to 20,000 ohms. If the reading is too low or shows infinity, there's likely a problem with the coil.

Testing the Ignition Coil with the Engine Running

Sometimes, the only way to test the ignition coil is by running the engine. However, this should only be done after conducting the previous tests and if necessary, as it involves connecting the spark plug to the coil and then to the engine block.

You'll need a spark plug tester or homemade tester to see the spark. With the engine running, the spark should be strong and regular. If it's weak, intermittent, or non-existent, your ignition coil may be faulty.

AD

Checking the Spark Plug Gap

Before testing the ignition coil with the engine running, ensure your spark plug gap is correct. The gap can cause misfires if it's too small or too large. The proper gap can be found in your vehicle's owner's manual.

Once you've checked the spark plug gap, proceed with the running test if necessary. Remember, safety should always be your top priority when working with your engine.

If, after following this guide, your ignition coil tests okay, move on to checking other components like the spark plug, ignition wires, and distributor cap. It's not uncommon for these to cause similar symptoms. But if your ignition coil tests faulty, replacement may be necessary. Consider having it done professionally if you're not comfortable doing it yourself to ensure your engine runs smoothly and safely. Happy diagnosing!

AD
AD