how to test kohler ignition coil with multimeter

Testing Kohler Ignition Coil with Multimeter: Step-by-Step Guide

By Christopher Hernandez
AD

Testing a Kohler ignition coil with a multimeter is a straightforward process that can help you diagnose engine performance issues. A faulty ignition coil can cause misfiring, reduced power, or the engine not starting at all. Let's walk through the procedure to test your Kohler ignition coil reliably.

Before you start, ensure you have a multimeter, a socket wrench, and safety gloves to protect you during the process. Also, make sure your engine is cold to prevent any burns. Now, let's dive into the testing process.

Understanding Kohler Ignition Coil

First, let's clarify what an ignition coil does. It steps up the voltage from the vehicle's electrical system to create a spark strong enough to ignite the fuel in your engine's cylinders. It consists of a primary and secondary winding, with the primary receiving a low-voltage signal and the secondary outputting a high-voltage spark.

AD
Test Any Ignition Coil With A Multimeter! (Easy DIY Tutorial!)
Test Any Ignition Coil With A Multimeter! (Easy DIY Tutorial!)
How to Test an Ignition Coil with a Multimeter (7-Step Guide)
How to Test an Ignition Coil with a Multimeter (7-Step Guide)
How To Test And Troubleshoot Ignition Coils - Hunker
How To Test And Troubleshoot Ignition Coils - Hunker

In a Kohler engine, the ignition coil is typically integrated into the ignition module. However, the testing process remains similar to that of separate ignition coils.

Preparation: Accessing the Ignition Coil

Start by disconnecting the negative battery terminal to prevent any accidental shorts. Then, locate the ignition module on your Kohler engine. It's usually situated on the top of the engine near the spark plugs. Once found, disconnect the electrical connectors leading to the module.

How to Test Ignition Coil with Multimeter
How to Test Ignition Coil with Multimeter
a hand is pointing at an electrical outlet with a multimeter on the wall behind it
a hand is pointing at an electrical outlet with a multimeter on the wall behind it

To access the ignition coil, you might need to remove some other components like the spark plug wire(s), depending on your engine's design. Be meticulous when removing these parts to avoid any damage or misplacement.

Testing the Ignition Coil Primary Winding

Now that you've accessed the ignition coil, let's test the primary winding. Set your multimeter to ohms (Ω) and touch the probes to the terminals of the primary winding. In most cases, the ignition coil's primary winding should have a resistance of around 2 to 10 ohms, although this can vary by manufacturer and model.

AD

If your multimeter reads infinite resistance or it's open-circuit, it indicates a break in the coil's wire. If the resistance is much lower than expected or it's short-circuit, the coil has likely shorted internally. In either case, replace the ignition coil.

Testing the Ignition Coil Secondary Winding

The secondary winding of the ignition coil produces the high-voltage spark. Testing this requires a higher voltage reading on your multimeter, which most multimeters can handle. However, be cautious when measuring high voltages to avoid damaging your multimeter or causing an electrical shock.

Set your multimeter to the highest voltage setting, usually around 20,000 volts (20 kV). Touch the probes to the terminals of the secondary winding. A working secondary winding should have infinite resistance, indicating an open circuit. If it reads any lower value, the coil's insulation has broken down, and it should be replaced.

AD

Checking Spark Strength

To ensure your ignition coil is functioning correctly, you can also check the spark strength. Reconnect the ignition module and bring your engine to a running state. Ground your multimeter's probe to the engine block and touch the other probe to the spark plug wire. The multimeter should read around 10,000 to 40,000 volts (10-40 kV) to indicate a healthy spark.

If the reading is much lower, the spark might not be strong enough to ignite the fuel efficiently, indicating a faulty ignition coil or other issues in the ignition system.

Testing your Kohler ignition coil with a multimeter is an essential maintenance procedure that can help you troubleshoot engine performance issues. Always ensure you follow safety guidelines when working on your engine, and if you're unsure about any part of the process, consult a professional mechanic.

AD
AD