how to test ignition coil on plug

How to Test an Ignition Coil on Plug: Step-by-Step Guide

By Melissa Rodriguez
AD

Every vehicle owner should know how to test an ignition coil, as it's a crucial component of your car's ignition system. A faulty ignition coil can cause your engine to misfire or fail to start altogether. In this guide, we'll walk you through the steps to test an ignition coil using simple, readily available tools.

Before we begin, ensure your engine is cool and that you have the necessary safety gear, including gloves and safety glasses. Also, make sure you have a multimeter, a spark plug wire puller, and a new spark plug for comparison.

Understanding Ignition Coil Basics

The ignition coil transforms the low-voltage battery power into the high voltage needed to create a spark at the spark plug. It does this by winding a copper wire around an iron core, creating a magnetic field. Understanding this principle is key to testing the ignition coil.

AD
an image of a car's fuel pump and its hose connected to the tank
an image of a car's fuel pump and its hose connected to the tank
How To Test And Troubleshoot Ignition Coils - Hunker
How To Test And Troubleshoot Ignition Coils - Hunker
How to Diagnose and Test an Ignition Coil
How to Diagnose and Test an Ignition Coil

There are two types of ignition coils: those with an internal ignition module (also known as 'smart' coils) and those without. The testing process for both is similar, but we'll focus on the more common type without an internal module.

Locating and Removing the Ignition Coil

First, locate the ignition coil by referring to your vehicle's repair manual. It's usually mounted near the engine's top near the spark plugs. Disconnect the negative battery cable to prevent any shorts once you start removing the ignition coil.

a man is working on an engine in his car, with the words spark plug below it
a man is working on an engine in his car, with the words spark plug below it
How to Test 3 Wire Coil on Plug with Multimeter (3 Ways)
How to Test 3 Wire Coil on Plug with Multimeter (3 Ways)

Loosen and remove the ignition coil's electrical connector, then unscrew and remove the coil from the engine. Be mindful of any brackets or retaining clips that might need to be removed or pressed in to release the coil.

Testing the Ignition Coil with a Multimeter

Once removed, use a multimeter set to resistance (ohms, Ω) to test the ignition coil. Most multimeter probes have a 'negative' and a 'positive' lead. The negative lead is usually black and can be inserted into either probe hole on the multimeter.

AD

Set your multimeter to the highest affichage (usually Ω), then touch both probes to the ignition coil's primary winding terminals (usually indicated by a lower voltage, like 12V or BAT).ñado your multimeter to the highest affichage (usually Ω), then touch both probes to the ignition coil's primary winding terminals (usually indicated by a lower voltage, like 12V or BAT).

Testing the Ignition Coil for a Spark

Before disconnecting the spark plug, it's crucial to test the ignition coil for a spark. This test helps verify the coil's ability to create the high voltage needed to ignite the air-fuel mixture.

To test, attach one multimeter probe to a metal part of the engine (like a bolt) and touch the other probe to the spark plug wire's center terminal. The multimeter should display a voltage reading in the thousands. If it doesn't, your ignition coil may be faulty.

AD

Testing the Spark Plug

If your multimeter shows no reading, the issue might not be with the ignition coil but with the spark plug. To test, remove the spark plug and attach the spark plug tester to the spark plug's center electrode. Ground the tester by touching its metal housing to a metal part of the engine.

If the spark plug tester doesn't spark, your spark plug is faulty. If it does spark, proceed to the next step.

Comparing with a Known Good Ignition Coil

Reinstall the spark plug (making sure to torque it to the manufacturer's specified torque) and reconnect the ignition coil. Remove a known good ignition coil from a working vehicle or use a new one for comparison. Reattach your multimeter probes to the ignition coil terminals.

AD

If the resistance reading on your multimeter is similar to that of the known good coil, your original coil may be functioning correctly. If not, your ignition coil is likely faulty and needs replacement.

Regularly testing your ignition coil can help diagnose issues early, saving you time and money in the long run. If you found your ignition coil faulty, replace it with a new one and reattach it to your vehicle. Always remember to consult your vehicle's repair manual for specific instructions. Safe driving!

AD