how to take agitator out of ge washer

How to Remove Agitator from GE Washer

By Mark Lewis
AD

Ever found yourself in a bind, staring at your whirring GE washer, only to realize that the agitator's decided to take a dive? Don't let it get you down. Taking out an agitator might seem like a daunting task, but with the right steps and a bit of patience, you'll have that agitator out in no time, ready for a fix or replacement. Let's dive in to learn how to remove an agitator from your GE washer safely and efficiently.

Before we start, safety first! Always remember to unplug your washer from the power source before you begin. This step is crucial to prevent any electrical accidents. Now, let's roll up our sleeves and get started.

Understanding Your Washer's Agitator

The agitator in your GE washer is the part that spins, creating an agitation effect to clean your clothes. It's connected to the transmission system, which is responsible for the spinning motion. Knowing this helps you understand what you're dealing with when it comes to removing the agitator. Let's dive into the types of agitators you might encounter.

AD
Agitator vs. Impeller Washer: Which to Choose?
Agitator vs. Impeller Washer: Which to Choose?
11+ Fantastic Ways to Clean a Washing Machine Agitator
11+ Fantastic Ways to Clean a Washing Machine Agitator
Replacing GE Washer Agitator
Replacing GE Washer Agitator

GE washers often come with two types of agitators: center post agitators and corkscrew agitators. Center post agitators are typically found in top-loaders and have a central post that the agitator is attached to. On the other hand, corkscrew agitators are found in both top-loaders and front-loaders and have a corkscrew-shaped design that helps to lift and drop clothes to create agitation.

Preparing Your Washer for Agitator Removal

Before you begin, you'll need to prepare your washer. First, remove any visible screws or bolts that hold the agitator in place. These are usually found at the bottom of the washer, either around the perimeter of the agitator or beneath a capscrew.

a close up of a toilet with the words how to remove detergent build - up from a washer
a close up of a toilet with the words how to remove detergent build - up from a washer
GE Washer Troubleshooting - How to Find Error Codes, and Reset a GE Washer
GE Washer Troubleshooting - How to Find Error Codes, and Reset a GE Washer

Next, partially drain the washer. You can do this by running a cycle with the drain hose disconnected or by using the drain pump (if your washer has one). This step is essential to prevent water from spilling out when you remove the agitator. Once you've drained the washer, grab a towel to soak up any remaining water.

Removing the Agitator from Your GE Washer

Now that your washer is prepared, it's time to remove the agitator. For center post agitators, you'll need to remove the cap or button that sits in the center of the agitator. This is usually held in place by a screw or a press-fit design. Once you've removed the cap, the agitator itself can be pulled out. You may need to use a flathead screwdriver or a putty knife to pry it out if it's stuck.

AD

For corkscrew agitators, the process is a bit different. You'll need to remove the detergent dispenser and the backsplash panel to access the agitator. Once you've done this, you'll find screws or bolts holding the agitator in place. Remove these, and the agitator should pop out with a little bit of wiggling and pulling.

Inspecting and Repairing Your GE Washer Agitator

Now that you've successfully removed the agitator, it's a good time to inspect it for any signs of wear and tear. The most common issues with washers are worn-out agitators, which can cause poor wash performance and excessive noise. If your agitator is worn out, you might consider replacing it with a new one.

However, if the issue isn't as severe, you can often fix it by cleaning the agitator and applying a small amount of lubricant. This can help reduce noise and improve performance. Always remember to clean the area where the agitator was located before putting it back in to prevent any blockages or malfunctions.

AD

Safety When Reinstalling the Agitator

When reinstalling the agitator, always ensure that it's properly aligned with the center post or the transmission system. For center post agitators, ensure the cap or button is securely fastened. For corkscrew agitators, ensure all screws or bolts are tightened properly to prevent any wobbling or excessive noise.

Once the agitator is back in place, plug your washer back in and run a test cycle to ensure everything is functioning correctly. If you're happy with the results, pat yourself on the back – you've just successfully removed and (hopefully) repaired the agitator in your GE washer!

Remember, if you're ever in doubt or encounter any issues, it's always a good idea to consult a professional repair technician. With the right knowledge and a little bit of care, you can keep your GE washer running smoothly for years to come. Happy washing!

AD
AD