how to remove agitator from amana washer

Step-by-Step: Removing Agitator from Amana Washer

By Ashley Young
AD

Is your Amana washer giving you trouble? One common issue is the agitator failing to work properly. The agitator is a crucial part of your washing machine, responsible for cleaning your clothes by moving them around during the washing cycle. If it's not working, it can lead to insufficient cleaning, damaging your clothes further. Let's guide you through removing the agitator from your Amana washer safely and effectively.

Before you begin any repair work, remember to unplug your washer from the power source to prevent any electrical accidents. Also, keep in mind that this process requires some technical skill and tools. If you're not comfortable performing these steps, we advise consulting a professional.

Gathering Materials and Preparing the Washer

First, you'll need to assemble your tools and prepare your washing machine for the repair. Ensure you have a screwdriver (often Phillips), an adjustable wrench, and a putty knife. These are common tools that you might already have around the house.

AD
Repair Washer Agitator, How To Clean Agitator In Washer, How To Replace Agitator On Whirlpool Washer, How To Replace Washing Machine Agitator, How To Repair Maytag Washing Machines, How To Fix Maytag Washing Machine, How To Clean Washing Machine Agitator, Ge Washer Agitator Replacement Instructions, How To Replace Washing Machine Stator
Repair Washer Agitator, How To Clean Agitator In Washer, How To Replace Agitator On Whirlpool Washer, How To Replace Washing Machine Agitator, How To Repair Maytag Washing Machines, How To Fix Maytag Washing Machine, How To Clean Washing Machine Agitator, Ge Washer Agitator Replacement Instructions, How To Replace Washing Machine Stator
Agitator vs. No Agitator? Which one is better.
Agitator vs. No Agitator? Which one is better.
How To Remove Agitator From A Whirlpool Washing Machine – Storables
How To Remove Agitator From A Whirlpool Washing Machine – Storables

Next, clear your work area by removing any items on top of your washer and, if possible, rolling the appliance away from the wall for easier access. Place a towel or a mat beneath the washer to protect your floor from any water spills.

Draining the Washer

Your washer may contain water from previous wash cycles. You need to drain this water to avoid a mess and prevent any short circuits. To drain, find the drain hose at the back of the machine, usually at the bottom. Unscrew the hose clamp, pull the hose out, and allow the water to drain into a bucket or the floor if it's level and can handle the water.

Kenmore Washer Repair – How to replace the Agitator Assembly
Kenmore Washer Repair – How to replace the Agitator Assembly
How to repair the Agitator Dogs in your Kenmore or Whirlpool, or etc. Washer
How to repair the Agitator Dogs in your Kenmore or Whirlpool, or etc. Washer

After the water has drained, reassemble the drain hose and clamp it back into place. This step might be different for top-loading washers, so always check your user manual for specific instructions.

Accessing the Agitator

To reach the agitator, you'll need to remove the inside panel of the washer. Start by opening the washer door and removing any residual water from the tub using a towel. Then, find and remove the screws holding the inner panel in place, locating them along the bottom of the washer or near the door hinge.

AD

Once the screws are removed, carefully lift the panel upwards and off, setting it aside. You should now be able to see the agitator and the driveshaft it's connected to.

Removing the Agitator

Before you disconnect the agitator, identify the set screw that holds it onto the driveshaft. You'll see a small hole in the agitator where the set screw is located. The set screw might be stripped and difficult to remove, depending on the age and wear of your washer.

Removing the Set Screw

Using a Phillips screwdriver, try to loosen the set screw. If it's too stripped, you might need to use a set screw extractor or a piece of metal to grip the screw and remove it. Be careful not to strip the screw hole further or cause damage to the agitator.

AD

If you're having trouble, you can use a way to grip the set screw rather than trying to turn the screw itself. A small piece of metal like brass wire or a thin nail can be used to grip the set screw and turn it out.

Disconnecting the Agitator

After removing the set screw, you should be able to slide the agitator off the driveshaft. You might need to use some force, but be careful not to damage the agitator or the driveshaft. If the agitator is still stuck, try using a putty knife to gently pry it off.

With the agitator removed, you can take a good look at the driveshaft and determine the next step – which could be repairing or replacing the driveshaft, depending on the issue and your washer's components.

AD

Congratulations! You've successfully removed the agitator from your Amana washer. It's now time to address the problem causing it to malfunction and repair or replace the necessary parts. After completing the repair, remember to reverse the disassembly process to reassemble your washer and restore it to working condition. Always double-check the space for any tools or parts that might have been left behind. Happy repairing!

AD