how to restring a kobalt electric weed eater

How to Restring a Kobalt Electric Weed Eater

By Melissa Lopez
AD

Every homeowner wants a well-maintained lawn, and Kobalt electric weed eaters are popular tools for achieving this. However, with regular use, the string on your weed eater will inevitably wear out and need to be replaced. Don't worry, restringing a Kobalt electric weed eater is a straightforward task that anyone can do with the right guidance. This comprehensive guide will walk you through the process, from gathering tools to trimming the new string to perfection.

Before you begin, it's important to ensure your weed eater is turned off and unplugged to avoid any accidents. Additionally, make sure you're working in a well-lit, stable area to prevent falls or drops that could damage your tool or injure you. With the basics covered, let's dive into the step-by-step process of restringing your Kobalt electric weed eater.

Gathering Your Tools and Materials

Before you start, assemble the following tools and materials:

AD
a person is holding an electric device with the words restring it up on it
a person is holding an electric device with the words restring it up on it
How to replace reload string on Kobalt 40V trimmer
How to replace reload string on Kobalt 40V trimmer
How to reload restring Hyper Tough (Walmart) 20V battery trimmer weed eater
How to reload restring Hyper Tough (Walmart) 20V battery trimmer weed eater
  • A new spool of trimmer line that matches your Kobalt weed eater's model
  • Screwdriver (usually Phillips or flathead, depending on your model)
  • Needle-nose pliers (optional, but helpful for handling small parts)

The first step in restringing your weed eater is to prepare the tool for maintenance. This involves accessing the spool housing, which holds the old string and accepts the new one.

Accessing the Spool Housing

Start by locating the spool housing on your Kobalt weed eater. It's usually a chamber on the bottom of the trimmer head, covered by a cap or a side panel. Using your screwdriver, unscrew and remove the cap or panel. Be sure to keep track of small parts to avoid losing them.

a man is holding an object in his hand and pointing to it with the words replace string
a man is holding an object in his hand and pointing to it with the words replace string

Once opened, you'll see the spool and the old trimmer line wrapped around it. On some models, there may be a cover or protective casing over the spool. Carefully remove this to expose the spool completely. Again, keep track of any small parts you remove.

Removing the Old Line

With the spool housing exposed, you're ready to remove the old trimmer line. First, find the two ends of the line, which should still be attached to the spool. If the ends are broken or frayed, use needle-nose pliers to carefully snip them as close to the spool as possible. This will make it easier to remove the old line and feed the new one through the trimmer head.

AD

Once you've located the ends of the old line, gently pull them to unwind the line from the spool. Continue pulling until the entire length has been removed from the spool and the trimmer head. If any residual line remains stuck to the spool or head, use your pliers to carefully remove it.

Preparing the New String

With the old line removed, it's time to prepare the new string for installation. Before you begin, consult your Kobalt weed eater's manual to ensure you're using the correct type and size of trimmer line for your tool. Most electric weed eaters use a lightweight, low-resistant line, but it's essential to double-check to avoid damage to your tool.

Once you've confirmed the correct line type, measure out the appropriate length for your weed eater. A good rule of thumb is to measure roughly three times the width of your trimmer head, but always refer to your manual for the most accurate measurement. Cut the line using a pair of sharp scissors or pruning shears to ensure clean, even ends.

AD

Threading the New String

Now that you have the new string measured and ready, it's time to thread it through the trimmer head and onto the spool. Locate the eyelet or hole on the side of the trimmer head where the line enters and exits. This is where you'll insert the new string.

Begin by inserting one end of the new string into the eyelet or hole on the side of the trimmer head. Push the string through until you have a few inches of line extending out both sides of the trimmer head. This will make it easier to feed the string onto the spool and ensure proper tensioning.

Winding the New String onto the Spool

With the new string fed through the eyelet, it's time to wind it onto the spool. Start by finding theocomponent on the spool that marks the starting point for winding. This is usually a small notch, an arrow, or a written indicator. Position the end of the new string at this mark, ensuring it's securely against the spool.

AD

Begin winding the string around the spool in the direction indicated by the winding arrow (there is usually one on the spool or in the user manual). Keep the string taut and evenly spaced as you wind to ensure proper tension and feeding during use. Continue winding until you've reached the end of your measured string length, leaving a few inches of line extending out of the trimmer head.

Reassembling the Trimmer Head

With the new string wound onto the spool, it's time to reassemble the trimmer head and prepare your Kobalt weed eater for use. First, ensure that both ends of the new string are still exiting the trimmer head eyelet, with a few inches of line extending out each side. If the string is too short or too long, adjust it now to ensure proper functioning.

Next, replace the protective casing or cover over the spool, if present. Ensure that the new string is not caught or hindered by this component during the replacement process. Some models may require you to feed the string through a specific slot or hole in the protective casing.

Reattaching the Trimmer Head Cover

With the protective casing (if any) in place, the final step is to reattach the trimmer head cover or cap. Align the cover with the trimmer head and screw it back into place using your screwdriver. Ensure that the cover is securely fastened but not overtightened, as this could damage the spool or cause the string to feed improperly.

Once the trimmer head cover is reattached, your Kobalt electric weed eater is ready for use. However, before you hit the lawn, perform a quick test to ensure the string is feeding correctly.

Performing a Test Run

Plug your weed eater into a power source and turn it on. Once it's running, place your hand near the trimmer head to feel the air flow. As the weed eater operates, the string should automatically feed out from the trimmer head, creating a cutting arc. If the string is feeding properly, you should feel a consistent, even breeze against your hand.

After a few seconds, turn off and unplug the weed eater. Inspect the length of the string extending from the trimmer head. If the string feeds too quickly or not at all, adjust the length or tension of the string to achieve the proper cutting arc. Once you've verified that the string is feeding correctly, your Kobalt electric weed eater is ready to tackle your lawn's toughest weeds and overgrowth.

Regularly maintaining your Kobalt electric weed eater not only extends its lifespan but also ensures optimal performance and safety. Restringing your tool is just one aspect of this upkeep, so be sure to consult your user manual for additional maintenance tips and guidelines. Happy trimming!

AD