how to replace valve cartridge on shower

Step-by-Step Guide: How to Replace a Shower Valve Cartridge

By Jessica Thompson
AD

Is your shower giving you fits lately, with a drip-drip-drip that's driving you up the wall? You might be dealing with a worn-out valve cartridge. Don't panic, because replacing it is a task you can tackle yourself. Let's dive into how you can replace your shower valve cartridge, step by step.

First things first, before you start unscrewing anything, make sure you have the right tools and parts. You'll need a flathead screwdriver, an adjustable wrench, a Phillips screwdriver, some plumber's tape, and a new shower cartridge, of course. Always double-check your cartridge matches your valve model. Now, let's get started.

Safety First: Preparation and Draining the Shower

Safety is key when dealing with water and electricity. So, before you begin, turn off the water supply and power to your shower. The water supply valve is usually located near your shower. If it's a wall-mounted shower, you might need to access it from the switch panel. Then, drain the remaining water from the shower pipe by turning on the faucet until it runs clear.

AD
an old toilet is being cleaned with water hoses
an old toilet is being cleaned with water hoses
How to Replace a Leaky Shower Valve Cartridge - HandyManHowTo
How to Replace a Leaky Shower Valve Cartridge - HandyManHowTo
Your Guide to Replacing a Shower Cartridge - DIY Bathroom Improvement!
Your Guide to Replacing a Shower Cartridge - DIY Bathroom Improvement!

Next, label your wires before removing them. This might seem unnecessary now, but trust us, it'll save you a lot of head-scratching later. Also, lay down a towel or a plastic sheet to catch any draining water or parts that might drop.

Removing the Shower Faceplate and Handle

The first thing you need to remove is the shower faceplate. Most faceplates are held in place with screws. Use a Phillips screwdriver to remove them. If your faceplate is held by a set screw, use an Allen wrench to remove it.

How to Replace Two-Handle Shower Valve? | Replace Two-Handle With Showers
How to Replace Two-Handle Shower Valve? | Replace Two-Handle With Showers
How to Change the Cartridge of a Delta Monitor Shower Valve.
How to Change the Cartridge of a Delta Monitor Shower Valve.

Now, it's time to remove the handle. Here's where the type of shower valve you have comes into play. For a single-handle shower, you'll usually find a screw on top or underneath the handle. Use a flathead screwdriver to remove this screw, then pull off the handle. If your handle is held in place by a setscrew in the brass escutcheon, use an Allen wrench to remove it.

venson Cartridges

Veson cartridges are some of the most common in showers. They're usually coated in plastic and come in a few different sizes. To remove a Veson cartridge, start by removing the bonnet nut using an adjustable wrench. You might need to use some force, so be careful not to strip the nut. Then, simply pull out the cartridge.

AD

When you put in the new cartridge, make sure the springs go back in as well. Hand-tighten the bonnet nut, because it's easy to overtighten and strip the threads. Be sure to use plumber's tape on the threads as you put everything back together.

Moen Cartridges

Moen cartridges are a bit more complex than Veson cartridges. They use a cam to control the valve, which is hidden behind the cartridge. To remove a Moen cartridge, start by removing the retaining clip. You can usually pry it out with a flathead screwdriver. Then, use a pair of pliers to pull out the pin that holds the cam in place.

Once the pin is out, you should be able to remove the cam and cartridge. Putting in the new cartridge is the reverse of this, just remember to put the retaining clip back in place once you've re-installed the cartridge.

AD

Reassembling Your Shower

Now that your new cartridge is in place, it's time to put everything back together. Start by reinstalling the handle, being sure to put the screw back in its original position. Remember to keep the wires labeled so you can put them back where they were.

Next, reinstall the faceplate. If you don't have the original screws, make sure you replace them with similar threads. Also, don't overtighten the screws or you might strip the faceplate.

Finally, turn the water supply back on and check for any leaks. If there are no leaks, you've successfully replaced your shower valve cartridge! Don't forget to test your shower to ensure the water temperature and pressure are correct.

AD

Just remember, patience is key when it comes to DIY projects like this. If you're unsure about any step, don't hesitate to consult a professional. But with these steps, you're well on your way to enjoying a leak-free, drip-free shower once again. Happy DIY-ing!

AD