how to install a shower valve with pex

How to Install a Shower Valve with PEX: Step-by-Step Guide

By Hannah Wilson
AD

At some point, most homeowners will need to tackle a plumbing project to update or repair their bathroom. Installing a shower valve with PEX tubing, a flexible and durable option, can be a straightforward DIY task. Let's guide you through this process step by step.

PEX, or cross-linked polyethylene, offers numerous benefits over traditional copper or chlorinated polyvinyl chloride (CPVC) pipes. It's resistant to scale and corrosion, reduces noise from water flow, and allows for easier bending and connections. However, like any plumbing project, it's essential to follow safety guidelines and have basic tools on hand.

Gathering Tools and Materials

Before starting, ensure you have all necessary tools and materials. This includes a PEX manifold valve, PEX tubing, stainless-steel PEX clamps, a tubing cutter, a PEX expander tool, teflon tape, and, for safety, work gloves and safety glasses.

AD
Delta Diverter Valve Installation with PEX B
Delta Diverter Valve Installation with PEX B
How to Install a Shower Valve with PEX A and SharkBite Plumbing - BEGINNERS Guide
How to Install a Shower Valve with PEX A and SharkBite Plumbing - BEGINNERS Guide
DIY How to Install a Shower Valve using Pex Plumbing
DIY How to Install a Shower Valve using Pex Plumbing

It's also crucial to choose the correct manifold valve based on your shower setup. If you're replacing an existing valve, ensure the new one has the same port size and configuration (3-way, 4-way, etc.).

Shutting Off Water and Disconnecting Old Pipes

Begin by turning off the water supply to your shower at the main water source. This is usually done at the water heater or via a dedicated shutoff valve near the shower. Once the water is off, open the shower to release any remaining pressure and prevent leaks.

How to - Install a Shower Valve using Pex Tubing Plumbing & Sharkbite connectors EASY - DELTA Faucet
How to - Install a Shower Valve using Pex Tubing Plumbing & Sharkbite connectors EASY - DELTA Faucet
463K views · 2.2K reactions | Shower valve plug tips…I finished installing the valve but have to plug the shower head drop ear. One way to do it is with a copper plug and SharkBite Max cap. I like this option because I can swap it out for a washing machine angle valve which helps me get water to the shower for thin-mortar and joint compound 🔥#plumbing #bathroomremodel #diy #sharkbiteplumbing #homerepairtutor | Home Repair Tutor | Facebook
463K views · 2.2K reactions | Shower valve plug tips…I finished installing the valve but have to plug the shower head drop ear. One way to do it is with a copper plug and SharkBite Max cap. I like this option because I can swap it out for a washing machine angle valve which helps me get water to the shower for thin-mortar and joint compound 🔥#plumbing #bathroomremodel #diy #sharkbiteplumbing #homerepairtutor | Home Repair Tutor | Facebook

Next, disconnect the old pipes from the shower valve. If you're replacing a traditional copper or CPVC setup, you'll likely use a hacksaw to cut the pipes and remove them. If your existing setup is already PEX, you can reuse the tubing and only remove the old valve.

Preparing the PEX Tubing

Measure and cut the PEX tubing to length, ensuring it extends about an inch beyond the end of the manifold valve. Use a tubing cutter for clean, precise cuts. Then, use the PEX expander tool to flare the ends of the tubing. This creates a space where the stainless-steel clamps will sit.

AD

It's essential to use dedicated PEX clamps and not regular hose clamps. PEX clamps have a built-in O-ring that provides a tight, durable seal. Wrap the flared end of the tubing with teflon tape to further enhance the seal. Be careful not to get tape on the exterior of the flared end or inside the tubing.

Installing the Manifold Valve

Before installation, apply plumber's grease (not WD-40) to the O-ring on the valve's ports to create a better seal. Then, insert the PEX tubing into the valve, pushed all the way in until you can't see the flared end. Next, carefully slide the PEX clamp over the tubing and onto the valve's port. Use a PEX crimping tool to secure the clamp, creating a tight, sealed connection.

Repeat this process for all ports on your manifold valve, ensuring each connection is tight and secure. If you're unsure about any connection, it's better to double-check and tighten rather than risking a leak. Once all connections are secure, turn the handle to test the valve's function.

AD

Connecting to the Showerhead and Walls

After successfully connecting the PEX tubing to the manifold valve, it's time to connect the other end to your showerhead and ensure it's properly secured to the wall. If your showerhead is already PEX, use the same process of flaring, wrapping, clamping, and crimping. If it's not, you'll need an adapter to connect the PEX tubing to the showerhead.

To secure the PEX tubing to the wall, you can use either wall brackets or AngleStop clamps, depending on your preference and the layout of your bathroom. The primary goal is to ensure the tubing is secure and won't move or kink, which could cause leaks or affect water flow.

Pressure Testing and Final Checks

Before turning the water supply back on, perform a pressure test to ensure there are no leaks. You can use a pressure test gauge, available at most hardware stores, to do this. If your pressure holds steady at 50-80 PSI for 15 minutes, you should be good to go.

AD

Once you've passed the pressure test, turn the water supply back on and test your shower. Start with low water pressure, gradually increasing it to check for leaks. If everything is secure and functioning correctly, you're all set! You've successfully installed a shower valve with PEX tubing.

Regularly inspect your PEX piping for any signs of damage or wear, and always turn off the water supply before making any adjustments to your plumbing. Happy DIY!

AD