how to install a shower valve delta

Easy Delta Shower Valve Installation: Step-by-Step Guide

By Hannah Harris
AD

Installing a shower valve, particularly a Delta one, can significantly enhance your shower's functionality and aesthetics. Here's a comprehensive, step-by-step guide on how to do this, ensuring your project is both safe and satisfying.

Delta shower valves are known for their durability and ease of installation, offering a range of designs to fit various bathroom decors. Before we dive into the process, ensure you have the right tools: an adjustable wrench, a flathead screwdriver, Teflon tape, and your Delta shower valve kit.

Preparation: Understand Your Valve and Setup

Delta offers several types of shower valves, each with specific installation requirements. Ensure you understand which type you have: a tub and shower valve, shower-only valve, or a thermostatic valve.

AD
an old toilet is being cleaned with water hoses
an old toilet is being cleaned with water hoses
Delta Diverter Valve Installation with PEX B
Delta Diverter Valve Installation with PEX B
How to - Install a Shower Valve using Pex Tubing Plumbing & Sharkbite connectors EASY - DELTA Faucet
How to - Install a Shower Valve using Pex Tubing Plumbing & Sharkbite connectors EASY - DELTA Faucet

Also, familiarize yourself with your bathroom's plumbing setup. Identify the existing hot and cold water supply lines and the branch where the shower valve will be installed.

Gather Tools and Parts

As mentioned earlier, you'll need an adjustable wrench, a flathead screwdriver, and Teflon tape. Your Delta shower valve kit should include the valve, plastic sleeves, brass parts (including screws and washers), and a faceplate.

How to Install a Shower Valve Cartridge - HandyManHowTo
How to Install a Shower Valve Cartridge - HandyManHowTo
How to Install a Delta Single Lever Shower Valve | ehow.com
How to Install a Delta Single Lever Shower Valve | ehow.com

DIY Tip: Always keep a small bucket or tray to catch any parts or screws that might fall into the wall cavity during disassembly. It's also a good idea to lay down a towel or drop cloth to protect your floor.

Turn Off Water Supply and Test

Before you start, turn off the main water supply valves leading to your shower. Usually, these are located either near the showerhead or under the access panel in your shower wall.

AD

Next, open the shower's hot and cold faucets to relieve any remaining water pressure. Double-check that water is no longer flowing by testing it with a cup or by running your hand under the faucet.

Removing the Old Shower Valve

With the water supply turned off, it's time to remove the old shower valve. This process can vary slightly depending on the existing valve's design, but here's a general guideline:

Start by removing the escutcheon (the protective plate around the faucet stalk) using your flathead screwdriver. Then, use your adjustable wrench to loosen and remove the locknuts, which secure the faucet handles to the valve body.

AD

Disconnect the Water Supply Lines

Using your adjustable wrench, carefully unscrew the water supply lines from the valve body. You may need to cut off any existing Teflon tape to facilitate removal.

Once the lines are free, wrap the end of each line with Teflon tape (up to six wraps) to prevent leaks when you reconnect them later.

Remove the Old Valve

With the supply lines disconnected, the old valve should be easily removed from the wall. If it's stubborn, try gently wiggling it back and forth while pulling it out.

AD

The valve body might be attached to the wall with plastic sleeves or metal brackets. Remove these as needed, but be careful not to damage your wall.

Installing Your Delta Shower Valve

Now that you've removed the old valve, it's time to install your new Delta shower valve. Start by inserting the new valve body into the wall cavity, ensuring it's tightly secure.

Reconnect the water supply lines, making sure they're properly oriented (hot on the left, cold on the right) and fully tighten them using your adjustable wrench. Remember to wrap the male ends with Teflon tape before reattachment to create a leak-free seal.

Install the Valve Trim

Install the plastic sleeves onto the valve body, followed by the brass nut and washer. Tighten the nut by hand, then use your adjustable wrench to snug it further. Be careful not to overtighten.

Next, install the handle operators, ensuring they match the correct hot and cold orientation. Secure them with the set screws provided in the kit.

Add the Faceplate and Test

Finally, install the faceplate to cover the escutcheon, giving your shower valve a finished look. Ensure all parts are properly secured and that the handles turn freely.

Slowly turn the water supply back on and test your new Delta shower valve. Check for any leaks around the base of the valve and ensure the water temperature adjusts smoothly.

Congratulations! You've successfully installed your new Delta shower valve. Enjoy your updated shower experience and the satisfaction of a job well done. Don't forget to dispose of any used parts responsibly and recycle what you can.

AD