how to replace moen shower handle

**Step-by-Step: How to Replace a Moen Shower Handle**

By Daniel Smith
AD

Is your Moen shower handle giving you trouble? Don't let a faulty handle ruin your bathing experience. Replacing it is a DIY project that saves you time and money. Follow our step-by-step guide to learn how to replace a Moen shower handle safely and efficiently.

Before you start, make sure you have the right tools and the correct replacement part. This guide assumes you're replacing a standard, single-function handheld Moen shower handle. If you have a different model or a two-function one, you may need additional parts.

Preparation and Removing the Old Handle

First, gather your tools. You'll need an adjustable wrench, a flathead screwdriver, Teflon tape, and a backup clip (if not included with your new handle). Also, ensure your replacement handle is identical to the old one, with the same function and fitting.

AD
How To Replace A Single-Handle Shower Cartridge | 1-Tom-Plumber
How To Replace A Single-Handle Shower Cartridge | 1-Tom-Plumber
How to Replace Two-Handle Shower Valve? | Replace Two-Handle With Showers
How to Replace Two-Handle Shower Valve? | Replace Two-Handle With Showers
How to Remove Shower Handle Sans Screws: DIY Guide
How to Remove Shower Handle Sans Screws: DIY Guide

Start by turning off the water supply. Locate the shut-off valves under your sink or near your water heater and turn them clockwise to close. Next, open the faucet to release any remaining water pressure.

Accessing the Handle Base

Remove the existing handle from your shower. Most Moen handles can be removed by simply unscrewing the set screw (usually located on the top) with a flathead screwdriver. Once unscrewed, gently pull the handle off.

What To Do When Replacing a Shower Valve Gets Complicated
What To Do When Replacing a Shower Valve Gets Complicated
Updating an old Moen shower valve with pictures. TL473 or TL470
Updating an old Moen shower valve with pictures. TL473 or TL470

Next, use an adjustable wrench to loosen and remove the escutcheon or base plate that covers the water supply lines. Once removed, you should see the bell housing, where the handle connects to the water supply.

Disconnecting the Water Supply Lines

Using your adjustable wrench, carefully loosen and remove the coupling nuts that secure the water supply lines to the bell housing. You might need to use some force, but be cautious not to damage the lines or the threading.

AD

Once the nuts are removed, gently pull the water supply lines away from the bell housing. You may need to use a बेहज pliers to help grip and remove them if they're stuck. Be prepared for some water to leak out, and have a towel ready to absorb it.

Installing the New Moen Shower Handle

With the old handle and supply lines removed, it's time to install the new one. First, ensure your new handle comes with a seat washer. If it doesn't, you'll need to purchase one separately.

Before installing the new handle, wrap the threads of the cold water supply with Teflon tape. This helps create a watertight seal, preventing leaks. Wrap the tape clockwise, starting at the base of the threads and overlapping each layer by about half.

AD

Attaching the New Handle to the Bell Housing

Begin by screwing the seat washer onto the bell housing by hand. Once the seat washer is in place, screw on the new handle. Hand-tighten the handle as much as you can, then give it an extra quarter to half turn with a wrench.

Be careful not to overtighten the handle, as this can strip the threads or break the handle. If your new handle came with a backup washer, install it now by hand at the base of the handle.

Reattaching the Water Supply Lines and Escutcheon

Reconnect the hot and cold water supply lines to the bell housing. Using your adjustable wrench, tighten the coupling nuts by hand as much as possible, then give them another quarter to half turn.

AD

Replace the escutcheon or base plate, ensuring it covers the supply lines and bell housing completely. If necessary, use screws to secure the escutcheon in place.

Final Checks and Testing

Before turning the water supply back on, open the faucet to relieve any remaining air in the system. Then, slowly turn the water supply valves counterclockwise to open them.

Once the water is turned back on, slowly open the shower faucet to test the new handle. The water should flow smoothly without any leaks around the handle or base. If there are no leaks, you've successfully replaced your Moen shower handle!

Don't forget to properly dispose of your old handle and any used parts. If you encounter any issues or need further assistance, don't hesitate to contact a professional plumber.

AD