how to replace kenmore dryer door switch

How to Replace Kenmore Dryer Door Switch

By William King
AD

Is your Kenmore dryer acting up, specifically when it comes to opening and closing? The culprit could be a faulty door switch, a common issue in dryers. Don't worry, replacing the door switch is a straightforward process that doesn't require a professional. Let's guide you through the simple steps to replace your Kenmore dryer door switch.

Before you start, ensure you have the right parts and tools. You'll need a new door switch, which can be found at appliance parts stores or online. Additionally, you'll need a flathead screwdriver, a nutdriver, and maybe a pair of pliers if the switch is hard to remove.

Understanding Your Kenmore Dryer's Door Switch

First, understand what the door switch does. The door switch, or interchangeably called a door interlock switch, ensures your dryer doesn't run when the door is open. It's a safety feature to prevent fires and injuries.

AD
an image of a leaking door switch
an image of a leaking door switch
How To Replace Dryer Door Switch - Dryer won't start - Whirlpool/Kenmore
How To Replace Dryer Door Switch - Dryer won't start - Whirlpool/Kenmore
DIY Kenmore Dryer Door Switch Replacement: Step-by-Step Guide
DIY Kenmore Dryer Door Switch Replacement: Step-by-Step Guide

The switch is usually located behind the control panel, under the lint filter, or near the door. Its lifespan is typically shorter than that of the dryer itself, hence why you might need to replace it.

Identifying the Door Switch

Once you've accessed the area where the door switch is located, identify the switch. It's usually a small rectangular or circular plastic component with two or more wires connected to it.

How to Bypass Dryer Door Switch
How to Bypass Dryer Door Switch
How to replace a dryer door switch | Repair guide
How to replace a dryer door switch | Repair guide

If you're unsure, consult your dryer's manual or look up a diagram online. Model numbers and switch locations can vary, so it's crucial to confirm you've found the right part.

Preparing Your Dryer for Switch Replacement

Before you start, ensure your dryer is unplugged from the power source. This is a safety measure to prevent electrical shocks. If your dryer is hardwired, turn off the circuit breaker.

AD

Next, clear the area around the dryer. You'll need space to work, and it's best to keep the workspace clean to avoid misplacing small parts. If your dryer has a pedestrian control panel, you might need to remove it. Use your flathead screwdriver to do this.

Removing the Old Door Switch

Now that you're ready, let's remove the old door switch.

First, disconnect the wires from the switch. They might be held in place by a plastic clip, which you can pry open with your screwdriver. If the wires are taped, carefully remove the tape.

AD

Removing the Mechanical Component

The switch is usually held in place by screws or a clip. Use your screwdriver to remove the screws, or your pliers to prize open the clip. Some switches might be a press-fit, requiring you to twist and pull it out.

Be careful while removing the switch, as it might be attached to a microswitch. If it is, you'll need to disconnect that as well. Microswitches can look similar to the door switch, but they usually have three terminals instead of two.

Preparing the New Door Switch

Before installing the new switch, make sure it's identical to the old one. It should fit perfectly into the switch housing.

AD

If your new switch comes with its own terminals, strip about half an inch of insulation from the wire ends using your pliers. If it's a push-in type, you can skip this step.

Installing the New Door Switch

Now, let's get the new switch in place.

If your switch has terminals, connect the wires to their respective positions. Make sure to match the colors. If the switch is a push-in type, insert the wire ends into the holes and press down until you hear a click.

Once the wires are connected, secure the switch into the housing. If it was held by screws, use them to secure the new switch. If it was a clip or a press-fit, attach it the same way as the old one.

Testing the New Door Switch

Before reassembling your dryer, test the new switch. Close the dryer door and use a continuity tester or a multimeter to ensure the switch is working properly. When the door is closed, there should be continuity between the switch's terminals.

If the switch is working, reattach any panels you removed earlier. Plug your dryer back in or turn the circuit breaker back on. Run a test cycle to ensure the dryer is working correctly.

Replacing the Kenmore dryer door switch might seem like a complex task, but when you break it down, it's quite manageable. If you're unsure about any step, don't hesitate to consult a professional. Always prioritize safety and ensure you're comfortable with the process before proceeding.

AD