Step-by-Step Guide: How to Replace Your Amana Dryer Heating Element
Safety first! Before you begin, unplug your Amana dryer from the power source to prevent any electrical hazards.
Replacing an Amana dryer heating element isn't as daunting as it may seem. With a bit of patience and the right tools, you can get your dryer running efficiently again. Follow this step-by-step guide to help you troubleshoot and replace your heating element safely and effectively.
Understanding Your Amana Dryer Heating Element
The heating element in your Amana dryer is responsible for generating the heat needed to dry your clothes. When this part malfunctions, your dryer may not heat up, leading to longer drying times or ineffective cleaning.
Before you proceed, identify the type of heating element in your dryer. Presently, Amana uses two kinds: the coil element and the calrod heating element. The guide below covers both types.
Identifying the Heating Element
Depending on the model, the heating element in your Amana dryer could be located at the base or in the tumbler area. Inspect your dryer's user manual to understand the specific location in your model.
If the manual isn't available, consult the model number. For models between 2010-2018, Amana used both types of heating elements. For newer models (2019-present), Amana primarily uses the calrod heating element.
Gathering Tools for the Job
Before you start, make sure you have all the necessary tools:
- Screwdriver
- Pliers
- Wire stripper
- Wire nuts (if required)
- New heating element (ensure it matches your dryer's model and the type of heating element)
Removing the Old Heating Element
Now that you're ready, let's dive into the replacement process.
First, remove the dryer's access panel or back cover to expose the heating element. The method for removing this varies by model, so review your user manual or check the manufacturer's troubleshooting guide for your specific dryer.
Disconnecting the faulty heating element
Before you disconnect any wires, take a photo of the wiring for reference and easy reassembly.
For coil elements, you'll typically find two wires connected to the unit. Carefully cut these wires with your wire stripper, leaving about 1 inch of each wire exposed.
Calrod heating elements usually have three wires: two high-limit thermostat wires and one power wire. Carefully cut this wire, leaving around 1 inch of each wire exposed.
Removing the old heating element
After disconnecting the wires, locate the retaining screws securing the heating element. Remove these screws using your screwdriver.
Once the screws are out, pull out the old heating element from the dryer. If necessary, use pliers to gently remove any clogs or debris from the heating element housing.
Installing the New Heating Element
Now that the old element is out, it's time to install the new one.
Before you begin, ensure the new heating element matches your dryer's model and the type of heating element (coil or calrod).
Positioning the new heating element
Insert the new heating element into its housing, ensuring it's securely seated. For coil elements, position the heating element so the wires align with the wire connectors. For calrod elements, position the element so the three wire connectors stick out.
Securing and connecting the new heating element
Secure the new heating element in place with the appropriate screws, ensuring it's tightly fitted but not over-tightened.
Now, connect the new heating element to the wires you cut earlier. For coil elements, twist the exposed wires together and secure them with wire nuts. Ensure the polarities match those you photographed earlier.
For calrod elements, connect the two high-limit thermostat wires and the single power wire to the corresponding connector on the new heating element. Ensure the polarities match the original wiring configuration. Consult your original photograph for reference.
Testing the New Heating Element
Before plugging your dryer back in, it's essential to test the new heating element to ensure it's working correctly.
Wrap a small bundle of rags around one of the heating element's connectors. Plug the dryer back into the power source and turn it on. After a few seconds, if the rags heat up, your new heating element is working correctly.
Once you've confirmed the heating element is functioning properly, remove the rags and reassemble the dryer cover. Now your Amana dryer is ready to efficiently dry your clothes once again.
Should you encounter any issues or have doubts during the process, don't hesitate to consult a professional or contact Amana's customer support. Regular maintenance and proper usage will ensure your dryer serves you well for years to come.