how to remove rear brake calipers

How to Remove Rear Brake Calipers

By Sarah Johnson
AD

Removing rear brake calipers, while it may initially seem daunting, can be a breeze with the right know-how. This procedure is often necessary when replacing brake pads, upon noticing excessive wear, or if there's evidence of rust, corrosion, or damage on the unit. It's crucial, though, to ensure this task is carried out in a controlled, safety-conscious environment.

This guide will walk you through the step-by-step process, from gathering the necessary tools to safely reinstalling the calipers. Before we dive into the specifics, remember that the process might vary slightly depending on your vehicle make and model, so always consult your car's repair manual for model-specific advice.

Preparation: Tools and Safety Measures

Assembling the correct tools is your first step. You'll need a jack and jack stands for lifting the vehicle, a torque wrench, a C-clamp, or brake claw, socket wrenches, an assistant (optional but helpful), and of course, safety gear including gloves and eye protection. Don’t forget the consistently underestimated yet vital item - patience. Removing calipers takes time, care, and precision.

AD
Stop Ruining Rear Calipers! Use This Brake Rewind Tool Trick #shorts
Stop Ruining Rear Calipers! Use This Brake Rewind Tool Trick #shorts
the word cool trick on top of an image of a car's brake assembly
the word cool trick on top of an image of a car's brake assembly
How to Rebuild a Brake Caliper: Saturday Mechanic
How to Rebuild a Brake Caliper: Saturday Mechanic

Safety is paramount. Park your vehicle where there's ample space to work; ensure the parking brake is engaged to prevent any unwanted movement. Wheels can be chocked for added security. Finally, never skip wearing your safety gear. Minimal cuts and bruises from non-protected areas can be serious nuisances once you're deep into the task.

Blocking the Rotor

Ensure the rotor doesn't spin while you're working by blocking it. You can use a C-clamp or a brake claw for this. Place this tool on the inner part of the rotor, tightening it until it gently holds the rotor in place.

What Is the Red-Colored Auto Part Seen Inside the Tires of Certain Cars?
What Is the Red-Colored Auto Part Seen Inside the Tires of Certain Cars?
How To Remove Broken Snapped Brake Caliper Bolt
How To Remove Broken Snapped Brake Caliper Bolt

If you're using a C-clamp, place it over one spoke across the rotor so that one end of the clamp rests on the hub and the other bears against a spoke. Tighten the screw until the rotor is firmly held, but not so tight that you risk damaging or warping the rotor or breaking the clamp.

Breaking the Bond

Your caliper slid over the outer pad's metal backing plate when pushed into place. This could have left a sticky, caulk-like residue that helps form a bond that keeps the two stuck together. Do NOT hit, pry or peel this off, as it may damage the pad and cause leaks.

AD

Instead, carefully use a razor blade or utility knife to clean up this residue. For stuck-on residue, soften it with heat from a soldering iron or propane torch, then scrape it off. Be gentle, applying steady pressure to avoid damaging the pomegranate-textured surface of the pad.

The Actual Removal

By now, your caliper should be free of the outer pad and its protective plate. Now, it's time to disconnect the caliper from the vehicle itself. Before you start, mark the orientation of the caliper and brake line for precise reassembly.

Using a socket wrench, loosen and unscrew the lower caliper mounting bolt on the inboard side. You may need to disconnect the brake line for easier removal. Remember, always fasten any remaining nuts, bolts or screws back to their spots, or in a safe, recalls location to avoid confusion and loss.

AD

Prying the Caliper

The most common way to remove a rear caliper is to push the inner pad's backing plate slightly outwards so you can slip the caliper off the rotor. A C-clamp is helpful here, too. Place the C-clamp on the rotor with the mouth open widely. Slowly tighten the screw until the caliper assembly slides off the rotor and outer pad.

Professional mechanics often use larger jack-claw tools designed specifically for this task. Whatever you choose, keep the caliper piston extended while off the rotor to prevent corrosion and damage. Once the caliper is off, nestle it safely out of the way, ready to be reinstalled.

Aftermath: Inspection and Preparation for Installation

With the caliper off, check the entire brake system for leaks, corrosion, or damage. Measure and compare the thickness of both the outer and inner pads. If either is extremely thin, replace both.

AD

For damage on the caliper or its mounting brackets,:
- Light surface rust can be sanded, wiped, and painted over.
- Deeper corrosion must be addressed with sanding, chemical treatments, or replacement.
- Any cracks or severe scores will require replacement.

Before reattaching the caliper, ensure all components are clean and properly greased. A light smear of high-heat anti-seize compound around the caliper mounting bolts helps prevent seizing later. Also, ensure the caliper piston slides back smoothly for a secure fit during reinstallation.

Whenever you're working with your vehicle's brakes, ensure all parts are aligned correctly, And always remember to double-check and, if necessary, bleed your brake system post-reassembly. It's a good habit to get into, ensuring maximum safety post-repairs. Happy wrenching!

AD