how to remove blower motor

How to Remove a Blower Motor

By Olivia Brown
AD

Do you find that your car's blower motor is constantly running, even when the heater or AC is off? This could be an indicator that your blower motor is stuck and needs replacing. Removing a blower motor might seem like a daunting task, but with the right guidance and a few tools, it's a doable DIY project. Here's a step-by-step guide on how to remove a blower motor from your car.

Before we dive into the process, there are a few things you'll need: a socket wrench, flathead screwdriver, Phillips screwdriver, ratchet, extension, and a breaker bar. Having these tools on hand will make the process much smoother. Now, let's get started.

Preparation and Safety Measures

Before you begin, make sure to disconnect your car's negative battery cable to prevent any electrical shorts. Next, locate your blower motor, which is usually under the dashboard. You might need to remove some panels to access it. Once you've found it, take note of how it's connected, as this will help when putting it back together.

AD
How to Replace a Blower Motor in Your Car And Diagnosing
How to Replace a Blower Motor in Your Car And Diagnosing
Home Repair & Maintenance: How to Clean an Air Conditioner Blower Motor and Blade
Home Repair & Maintenance: How to Clean an Air Conditioner Blower Motor and Blade
How to replace a downdraft vent blower motor | Repair guide
How to replace a downdraft vent blower motor | Repair guide

This is also a good time to prepare your workspace. Lay out your tools and any parts you'll need to remove to access the blower motor. Having everything within reach will save you time and frustration.

Removing the Dashboard Trim and Cowl

Start by prying off the dash trim pieces using your flathead screwdriver. These are usually held in place by clips or screws. Be careful not to damage them as they're typically reusable. Once the trim is removed, you'll see the cowl, which needs to be unbolted.

The Expert’s Guide to Blower Motor Wiring Diagrams
The Expert’s Guide to Blower Motor Wiring Diagrams
Gemmy How To Airblown Inflatable Blower Motor Replacement
Gemmy How To Airblown Inflatable Blower Motor Replacement

Use your socket wrench to remove the bolts holding the cowl in place. You may need to use an extension and breaker bar for better leverage. Once the bolts are out, carefully remove the cowl and set it aside. You should now have a clear view of the blower motor.

Disconnecting the Wiring Harness and Hoses

Before you can remove the blower motor, you'll need to disconnect the wiring harness and any hoses connected to it. Start by tracing the wiring harness back to its connector and unplug it. Be sure to label or take a picture of the wiring harness connectors to ensure they go back in the correct spot.

AD

Next, locate any hoses connected to the blower motor and carefully disconnect them. You may need to use a pair of pliers to gently squeeze and pull the hose off the fitting. If there's any vacuum loss, you may need to bleed the system after the new motor is installed.

Removing the Blower Motor

With the wiring harness and hoses disconnected, you're finally ready to remove the blower motor. Locate the mounting screws or bolts holding the motor in place. These are usually found on the top or sides of the motor.

Using your socket wrench or ratchet, remove the screws or bolts. You may need to use an extension and breaker bar for better leverage. Once the screws or bolts are out, carefully pull the blower motor out of its housing. It might be snug, so you may need to wiggle it a bit.

AD

Inspecting the Blower Motor Housing

Now that the blower motor is out, take a moment to inspect the motor housing. Check for any signs of damage, corrosion, or excessive wear. If the housing is in bad shape, you may want to consider replacing it as well.

Also, make sure to clean out any debris or dust from the housing. This will help ensure that your new blower motor runs smoothly and doesn't shorten its lifespan.

Installing the New Blower Motor

Before installing the new blower motor, compare it to the old one to make sure they're identical. If they're not, double-check that you've ordered the correct replacement part.

AD

Once you're sure the new motor is a match, simply reverse the removal process to install it. Start by placing the new motor into the housing, then secure it with the mounting screws or bolts. Make sure they're tight, but not overtightened, as this could strip the threads or warp the motor.

Reassembly and Testing

Now that the new blower motor is installed, it's time to reassemble everything. Start by reconnecting the wiring harness and hoses, making sure they go back in the correct spots. Then, replace the cowl and dash trim pieces, securing them with the screws or clips you removed earlier.

Once everything is back in place, reconnect your car's battery. Then, start the engine and turn on the heater or AC to test the new blower motor. It should turn on and function properly without any unusual noises or smells.

If everything checks out, you're all done! You've successfully replaced your car's blower motor. Just remember to monitor the motor's performance over the next few weeks to ensure it continues to function properly. If it doesn't, you may need to troubleshoot any potential issues or take it to a professional mechanic.

AD