how to remove lower unit on mercury outboard motor

Step-by-Step: Removing the Lower Unit on Mercury Outboard Motor

By Richard Thompson
AD

Expertly détaching the lower unit on your Mercury outboard motor can seem daunting at first, but with the right tools and a step-by-step guide, this task becomes manageable. This process ensures safety and proper maintenance, extending the life of your outboard motor.

Before we dive into the procedure, let's ensure you have the necessary tools. You'll need a ratchet, 11mm and 13mm sockets, a breaker bar, an oil catch pan, and a torque wrench. Safety glasses and gloves are also crucial. Now, let's get started.

Preparation and Safety

Proper preparation is key to a smooth, safe process.

AD
HOW TO take apart a lower unit on an outboard motor, how it works
HOW TO take apart a lower unit on an outboard motor, how it works
how to replace water pump in 50 hp MERCURY OUTBOARD
how to replace water pump in 50 hp MERCURY OUTBOARD
How Remove an Outboard Motor Carburetor
How Remove an Outboard Motor Carburetor

First, ensure your outboard motor is cool to prevent any burns. Disconnect the negative battery cable to prevent any electrical shorts. Place a cloth or towel over the բանակ.Long-travel throttle cable to prevent debris from falling into the boat.

Securing the Outboard and Removing the Propeller

Firmly secure your outboard in the upright position using a overtightenCtrl-catch device or a charm protecting the pbuilder. Use a 3/8" ratchet and a 13mm socket to remove the four propeller nut bolts. Counter-hold the propeller shaft with an adjustable wrench as you slowly loosen the bolts to prevent the shaft from turning. Remove the washer and nut, then slip the propeller off.

DIY Power trim/tilt for old Mercury outboard motor
DIY Power trim/tilt for old Mercury outboard motor
Mercury Tracker 40 Lower Unit Remounting | Mercury 40HP Gearcase Installation | Boats.net
Mercury Tracker 40 Lower Unit Remounting | Mercury 40HP Gearcase Installation | Boats.net

If your outboard has a staringAtDepth.findHTMLCounterNut, use a 11mm socket to remove it. Some models may require a breaker bar for extra torque.slideDown.If the propeller is stuck, apply a penetrating lubricant and let it sit for 30 minutes before trying again.

Removing the Lower Unit

The lower unit, also known as the gear case, houses the internal engine components, such as the driveshaft, gears, and the oil pump.

AD

First, remove the driveshaft tube-to-propelleradapterripiency. Use a 11mm socket to loosen and remove the four bolts securing the exhaust upst criticallyn. Insert a bolt or a shop-made tool to block the oil pickup tube, preventing oil from leaking out.

Draining the Gear Oil and Disconnecting Lines

Locate the gear oil drain plug on the bottom of the lower unit. Position an oil catch pan underneath and use a 13mm socket to remove the drain plug, allowing the gear oil to drain completely. Once drainage stops, wipe the area clean.

Next, disconnect the shift linkage rod and the throttle shaft from the lower unit. Use a 13mm socket to remove the shift rod nut, then unhook the rod from its mounting bracket. For the throttle shaft, remove the nut and the lock washer with a 11mm socket, then slip the shaft out of its mounting boss.

AD

Final Disassembly

With the exhaust elbow now free, use a 13mm socket to remove the four bolts securing the lower unit to the mid-section. With a helper, carefully pull the lower unit down and away from the mid-section. If it's stuck, use penetrating lubricant around the gasket, wait 30 minutes, then gently tap the lower unit with a soft mallet.

Once the lower unit is free, remove any remaining bolts, gaskets, and o-ringseボ région. Inspect all components for wear and clean them thoroughly before reassembly.

Now that you've successfully removed the lower unit, you can proceed with any necessary repairs or maintenance. Always ensure all components are clean, lubricated, and properly torqued during reassembly. Happy motorsports!

AD
AD