how to remove the lower unit on a mercury outboard

How to Remove Lower Unit on a Mercury Outboard

By Steven Miller
AD

If you're a Mercury outboard enthusiast, you might find yourself in need of servicing or replacing parts in your lower unit at some point. To ensure safety and proper functioning of your outboard motor, it's crucial to know how to remove the lower unit. Here's a step-by-step guide on how to perform this task, along with some useful tips and potential issues to watch out for.

Before we dive into the steps, it's important to note that this process requires some mechanical aptitude and the right tools. It's also essential to ensure the outboard motor is cool and that all maintenance is performed in a well-ventilated area. Now, let's get started.

Gathering Necessary Tools and Preparing the Outboard Motor

The first step is to gather all the tools you'll need for the task. Having everything at hand will make the process smoother and more efficient. Here's a list of tools you'll need:

AD
a man in blue gloves working on a car with a wrench and other tools
a man in blue gloves working on a car with a wrench and other tools
how to replace water pump in 50 hp MERCURY OUTBOARD
how to replace water pump in 50 hp MERCURY OUTBOARD
How to Remove Lower Unit from 1966 Mercury 200 – Expert Guide
How to Remove Lower Unit from 1966 Mercury 200 – Expert Guide
  • Socket wrench set
  • Pliers
  • Screwdriver set
  • Oil catch pan
  • Funnel
  • Torque wrench (optional, but recommended)

Draining and Disconnecting the Lower Unit

Before you start removing any parts, you'll need to drain the lower unit.

  1. Tip the outboard motor upside down, ensuring the_propeller is clear of the ground.
  2. Place the oil catch pan underneath the drain plug located at the bottom of the lower unit.
  3. Using a socket wrench, remove the drain plug and allow the gear oil to drain completely.

Once the gear oil is drained, reconnect the drain plug and proceed to disconnect the lower unit.

DIY Power trim/tilt for old Mercury outboard motor
DIY Power trim/tilt for old Mercury outboard motor
Mercury Tracker 40 Lower Unit Remounting | Mercury 40HP Gearcase Installation | Boats.net
Mercury Tracker 40 Lower Unit Remounting | Mercury 40HP Gearcase Installation | Boats.net

Disconnecting the Shift and Thrust Linkages

Next, you'll need to disconnect the shift and thrust linkages.

  1. using a screwdriver, remove the shift rod support bracket and shift rod.
  2. Using a socket wrench, remove the nuts that secure the thrust linkage to the lower unit.
  3. Slide the thrust linkage away from the lower unit.

Removing the Lower Unit from the Outboard Motor

With everything disconnected and drained, you're now ready to remove the lower unit from the outboard motor.

AD

Supporting the Lower Unit and Removing Fasteners

Before you begin removing the fasteners, it's crucial to support the lower unit to prevent it from falling and causing damage.

  1. Position a jack or a piece of wood under the lower unit to support its weight.
  2. Using a socket wrench, remove the nuts and bolts that secure the lower unit to the outboard motor.
  3. As you remove each fastener, support the lower unit with your other hand to prevent it from falling.

Lowering and Removing the Lower Unit

Once all the fasteners are removed, the lower unit should be free to come off.

  1. Slowly lower the jack or remove the wood support, allowing the lower unit to lower down.
  2. Once the lower unit is completely free, carefully remove it from the outboard motor.

Congratulations! You've successfully removed the lower unit from your Mercury outboard. Now, you're ready to perform any needed maintenance, servicing, or replacement tasks.

AD

Remember to reassemble the lower unit following the reverse order of disassembly, using a torque wrench to ensure all fasteners are properly tightened. Always refer to your specific model's service manual for exact torque specifications. By following these steps carefully and taking your time, you'll be able to remove and reinstall the lower unit on your Mercury outboard like a pro.

AD