how to light rheem water heater pilot light

Reignite Your Rheem: How to Light Water Heater Pilot Light

By Mark Garcia
AD

Few things are as frustrating as waking up to a cold shower due to a faulty water heater. If your Rheem water heater is having trouble providing hot water, you might need to relight the pilot light. This straightforward process can save you the time and cost of calling a professional. Let's break it down step by step.

Before you start, ensure you have the following tools: a flashlight, a screwdriver, gloves to protect your hands, and safetyoggles. Also, make sure there are no flammable materials nearby in case of a small flame. Now, let's dive into the process.

Understanding the Rheem Water Heater Pilot Light

The pilot light in your Rheem water heater burns continuously, lighting the gas burner when you need hot water. When the pilot light goes out, the water heater can't heat the water. Here's how to relight it and restore your hot water supply.

AD
How to Check Water Heater Pilot Light | 6 Effective Steps (2026)
How to Check Water Heater Pilot Light | 6 Effective Steps (2026)
How To Light Pilot (Turn On) Water Heater. Honeywell Rheem whirlpool A. O. Smith. 
How To Light Pilot (Turn On) Water Heater. Honeywell Rheem whirlpool A. O. Smith. 
How to Relight your Water Heater Pilot Light
How to Relight your Water Heater Pilot Light

Rheem water heaters come with safety features that prevent the pilot light from being too easy to relight. Make sure you follow each step closely to ensure your safety and success.

Preparing Your Rheem Water Heater

Before you start, turn off the gas supply to your water heater. You can find the gas shutoff valve near the water heater, usually on the gas supply pipe. Use a wrench to turn the valve clockwise to shut off the gas.

5 Reasons Why Your Water Heater Pilot Light Won’t Stay Lit | Water Heater Hub
5 Reasons Why Your Water Heater Pilot Light Won’t Stay Lit | Water Heater Hub
How to Light or Relight Your Water Heater Pilot
How to Light or Relight Your Water Heater Pilot

Next, wait about 15 to 30 minutes to allow any residual gas in the system to dissipate. This step is crucial for safety. It may seem like an inconvenience, but it's to prevent any risk of gas pockets accidentally igniting.

Locating the Rheem Water Heater Pilot Light Assembly

The pilot light assembly is typically located at the bottom front of the water heater. You'll need to remove the access panel to expose the assembly. The panel is usually secured with screws, which you can remove with a screwdriver.

AD

Once you've removed the access panel, you'll see the pilot light assembly. It consists of a thermocouple (which monitors the pilot light), the pilot light itself, and the gas control valve. Your Rheem water heater's manual can provide a detailed diagram if you're unsure.

Relighting the Rheem Water Heater Pilot Light

Now that you've prepared your water heater and located the pilot light assembly, you're ready to relight the pilot light. The process involves turning a control valve, pressing a button, and using a match or lighter to ignite the gas. Let's break it down.

It's essential to follow these steps closely and not to rush the process. Remember, you're working with gas, which can be dangerous if not handled correctly.

AD

Preparing the Gas Control Valve

Begin by turning the gas control valve to the 'OFF' position and then to the 'PILOT' position. This action primes the system with gas, readying it for ignition. Keep the valve in the 'PILOT' position for the duration of this process.

Then, press and hold the 'PILOT' button while trying to light the pilot. The pilot light should ignite almost immediately. If it doesn't, don't keep pressing the button. Release the button and wait a few minutes before trying again. This gives any residual gas time to dissipate, reducing the risk of a gas pocket igniting unexpectedly.

Lighting the Pilot Light

Once you've pressed the 'PILOT' button, use a long-handled match or a long-reach lighter to ignite the gas. You should see a steady blue flame ignite. If the flame is yellow or doesn't burn steadily, there may be an issue with your water heater that requires professional attention.

AD

Keep the 'PILOT' button pressed for about 30 seconds to a minute after the flame ignites. This step helps ensure that the thermocouple can sense the pilot light, allowing the water heater to function correctly. Once you've held the button long enough, release it and turn the gas control valve to the 'ON' position.

Testing and Resetting the Rheem Water Heater

Now that you've relit the pilot light, you need to test your water heater and reset it to ensure it's working correctly. Here's how:

First, listen for the burner to ignite. You should hear it click and then ignite. If it doesn't, check that the thermostat is set between 110 and 140 degrees Fahrenheit. If the thermostat is set correctly, there may be an issue with the thermocouple or the gas supply.

Checking the Hot Water

Run some hot water through a faucet to ensure the burner ignited and the water is heating correctly. The first few drops may be cold because the burner only ignites after water begins to flow through the pipe. If the water isn't heating, there may be an issue with your water heater that requires professional attention.

If the water heater seems to be working correctly, turn off the hot water and let the system run for a few minutes. The water should remain hot. If it doesn't, there might be an issue with the thermostat or the thermocouple.

Now that you've successfully relit the pilot light and tested your Rheem water heater, you can enjoy hot water once again. Remember, if you're ever unsure about any part of the process or if there's an issue with your water heater, it's always best to call a professional. Your safety is the top priority. Happy hot showering!

AD