how to light bradford white water heater

Step-by-Step Guide: Lighting a Bradford White Water Heater

By Olivia Lopez
AD

Safety first! Before we dive into lighting up your Bradford White water heater, let's ensure we're fully prepared and understand the basics. Bradford White water heaters are a trusted name in the industry, known for their efficiency and durability. But like any appliance, they require proper and careful handling, especially when it comes to relighting.

Bradford White water heaters are equipped with safety features like thermal switches and a high-limit switch to prevent overheating. Before you start, ensure your heater has adequate ventilation as per the manufacturer's instructions. Now, let's get to the step-by-step guide on how to light your Bradford White water heater.

Preparation and Safety Measures

Before attempting to light your Bradford White water heater, ensure you've taken all necessary safety precautions. Remember, you're dealing with natural gas or propane, both of which can be highly flammable.

AD
How to Relight Pilot Light on Bradford White Water Heater
How to Relight Pilot Light on Bradford White Water Heater
Resetting Bradford White Water Heater - Ready To DIY
Resetting Bradford White Water Heater - Ready To DIY
Bradford White Water Heater Status Light Blinking [All Blinks Solved] - FireplaceHubs
Bradford White Water Heater Status Light Blinking [All Blinks Solved] - FireplaceHubs

Turn off the power to the water heater at the circuit breaker, and ensure the thermostat is in the 'Pilot' position. Allow the water heater to cool down for about 30 minutes to an hour before relighting. It's also a good idea to open a hot water faucet in your home to drain any excess pressure from the tank.

Locating the Pilot Light Assembly

Bradford White water heaters have a distinctive white cover on the front control panel. This cover protects the pilot light assembly and needs to be removed for you to access it. To do this, simply slide it out using your fingers. You should now see a small plastic tube, the thermocouple, and a wire connected to the gas control valve.

Bradford white water heater pilot light 2022 (Solved)
Bradford white water heater pilot light 2022 (Solved)
How To Light The Pilot On A Bradford White Water Heater
How To Light The Pilot On A Bradford White Water Heater

Beneath the control panel, you'll find the pilot burner assembly. This is where the pilot light is situated. Familiarize yourself with these components - you'll need to know where they are for the next steps.

Cleaning and Preparing the Area

Before relighting your water heater, ensure the area around the pilot light is clean and clear of any debris. Use a stiff wire brush to clean the pilot orifice, ensuring there's no blockage. If there is, you may need to use a small twist-tie or a thin, straightened wire to remove the obstruction.

AD

Once the area is clean, turn the gas control valve to the 'Pilot' position. This will release gas into the pilot burner. Now, press and hold down the 'Light' button located on the control panel. This will ignite the gas and light the pilot burner. Keep holding the button for at least 20 seconds to ensure the pilot light stays lit.

Resetting the Temperature and Thermostat

Once your pilot light is relit, you can reset the temperature and thermostat to your desired settings. Allow the water heater to run for a few minutes before turning on any hot water taps. This will allow the water heater to start heating the water in the tank.

After the water heater has been running for a few minutes, you can adjust the temperature on the thermostat to your desired setting. Bradford White water heaters typically have a factory setting of 120°F (49°C), which is considered a safe and energy-efficient temperature for most households.

AD

Checking the Pilot Light

After you've relit the pilot and allowed the water heater to heat the water in the tank, it's a good idea to check that the pilot light is burning correctly. Look through the holes on theaporator, and you should see a solid blue flame if everything is working correctly.

If the pilot light is burning Norbert or there's no flame at all, you may need to call a professional plumber. It could indicate a larger problem with your water heater, such as a cracked heat exchanger or a faulty thermocouple.

Safety Check and Final Steps

Before you wrap up, perform a final safety check. Turn the gas control valve to the 'On' position to ignite the main burner. If the burner ignites without any issues, you're good to go. If not, you may need to contact a professional for further assistance.

AD

Remember, it's always best to err on the side of caution when dealing with gas appliances. If you're unsure about any part of the relighting process, don't hesitate to call a licensed plumber. Regular maintenance and professional checks can prolong the life of your Bradford White water heater and ensure it's running safely and efficiently.

Congratulations, you've successfully relit your Bradford White water heater! Regularly checking and maintaining your water heater can prevent unexpected power outages. Don't forget to put a reminder in your calendar every six months to perform a quick check-up on your water heater and ensure it's running smoothly.

AD