how to drain a bradford white water heater

Step-by-Step: Bradford White Water Heater Drain Guide

By John Lopez
AD

Draining a Bradford White water heater isn't as complex as it might seem. Regular maintenance, including periodic draining, is crucial to ensure your water heater's longevity and efficiency. This guide will walk you through the process step by step, making sure your Bradford White water heater remains in tip-top shape.

Before we begin, ensure you have the necessary tools at hand. You'll need a flathead screwdriver, a garden hose, and possibly a bucket, depending on your setup. Also, remember to always disconnect the power or turn off the gas supply before starting any maintenance work on your water heater.

Preparing Your Bradford White Water Heater for Draining

Preparation is key when it comes to draining a water heater. You'll want to ensure there's minimal mess and maximum safety during the process.

AD
How to Drain a Clogged Water Heater
How to Drain a Clogged Water Heater
How To Drain Your Water Heater
How To Drain Your Water Heater
a man standing next to a water heater with the caption dad advice how to drain your water heater in 1 min
a man standing next to a water heater with the caption dad advice how to drain your water heater in 1 min

First, turn off the power or gas supply to your water heater. For electric models, simply flip the circuit breaker to the 'off' position. For gas models, locate the gas cock knob, usually near the bottom of the unit, and turn it to the 'pilot' setting.

Isolating the Water Supply

Next, you'll need to isolate the water supply to your water heater. This will prevent any water from entering or leaving the tank while you're draining it.

How to Unclog Water Heater Drain
How to Unclog Water Heater Drain
The BEST Step By Step Guide To Draining Your Water Heater
The BEST Step By Step Guide To Draining Your Water Heater

Locate the cold water supply valve, usually near the top of the water heater. Turn it clockwise to close it. If your water heater has a flexible supply line, you may also want to secure it with a clamp to prevent it from moving while you're draining the tank.

Relieving the Pressure in the Tank

Before you start draining your water heater, you'll need to relieve the pressure inside the tank. This is particularly important for gas models as the relief valve might release scalding water.

AD

Locate the temperature and pressure (T&P) relief valve on your water heater. It's usually a pipe that runs from the top of the tank to the floor. Open it by lifting the valve's lever or pushing the test lever down for about five seconds. Once the pressure is relieved, close the valve by pushing the lever back up.

Draining Your Bradford White Water Heater

Now that your water heater is prepared, it's time to start draining the tank.

Connect one end of your garden hose to the drain valve at the bottom of your water heater. Extend the other end of the hose to a suitable drain or outside, ensuring it's far enough away from any electrical devices to prevent water damage.

AD

Opening the Drain Valve

Slowly open the drain valve by turning it counterclockwise until water starts flowing out of the hose. If water doesn't flow out immediately, you may need to help it along by opening a hot water faucet in your home, which will allow air to enter the system and facilitate drainage.

Once water starts flowing, keep an eye on the drain hose to ensure it's not kinking or blocking. Allow the tank to drain entirely, which may take a few minutes to half an hour, depending on the size of your water heater.

Rinsing the Tank

After your Bradford White water heater has drained completely, close the drain valve and remove the hose. Now it's time to flush the tank to remove any sediment buildup.

AD

Slowly open the cold water supply valve and allow water to fill the tank until it's about one-third to one-half full. Then, open the drain valve again and allow the water to drain out. Repeat this process several times to thoroughly flush the tank.

Refilling and Restoring Power

Once your water heater's tank is clean and free of sediment, it's time to refill it and restore the power supply.

Turn the cold water supply valve back on fully and allow the tank to fill completely. This may take a while, so be patient. Once the tank is full, open a few hot water faucets in your home to allow the system to vent.

Reconnecting the Power Supply

Now that your water heater is refilled, it's time to reconnect the power supply. If you have a gas model, turn the gas cock knob back to the 'on' position and relight the pilot light as instructed in your owner's manual.

For electric models, simply flip the circuit breaker back to the 'on' position. Once the power is restored, your water heater should start heating the water and you can resume normal usage.

Regular maintenance, including periodic draining, is key to keeping your Bradford White water heater running smoothly and efficiently. So, mark your calendar and make sure to perform this task at least once a year. Safe DIYing!

AD