how to install shower head extension arm

Boost Your Shower Reach: Easy Guide to Install Shower Head Extension Arm

By Laura Moore
AD

A well-angled shower head can significantly enhance your bathing experience, especially when standing or using a tall showerhead. An extension arm can help achieve this perfection by adjusting the showerhead's position. Let's delve into how to install a shower head extension arm, optimizing your comfort and convenience.

Before we begin, ensure you have all the necessary tools and materials at hand. You'll need an adjustable wrench, tape measure, thread seal tape (Teflon tape), and of course, your extension arm and showerhead. Always double-check your plumbing supply company's specific installation instructions as variations might apply.

Preparation and Measurement

First, ensure you have the correct extension arm for your showerhead. Most extension arms are universal and fit standard ½-inch NPT connections. However, it's essential to confirm compatibility.

AD
How to Install an Adjustable Shower Arm by HammerHead Showers (raise or lower your shower head!)
How to Install an Adjustable Shower Arm by HammerHead Showers (raise or lower your shower head!)
7 of the Best Shower Head Extension Arms
7 of the Best Shower Head Extension Arms
a hand is holding onto the handle of a shower faucet
a hand is holding onto the handle of a shower faucet

Measure the existing height of your showerhead from the floor. Decide where you want the showerhead after installing the extension arm, ensuring it's high enough for tall users or those who prefer a standing spray. Most extension arms range between 6 to 12 inches in height, so choose accordingly.

Turn Off and Drain Water Supply

Begin by turning off the water supply to your shower at the main valve. Usually located in the bathroom, behind the bathroom wall, or in an adjacent room, this valve should be clearly marked or identified with a 'Hot' and 'Cold' tag. If you're unsure, turn off the main water supply to avoid any potential flooding.

Shower extension arm, flange, and head replacement
Shower extension arm, flange, and head replacement
How to install a rainfall shower head | Shower head extension arm
How to install a rainfall shower head | Shower head extension arm

Open the shower faucet to drain any residual water. This step is crucial to prevent water spillage during installation and ensure a clean work area.

Uninstall the Original Showerhead

Using an adjustable wrench, loosen and remove the original showerhead. Counter-clockwise motion is usually the correct direction. You may need to apply some force, but be careful not to overtighten or strip the threads. If the showerhead is old or significantly rusted, you might need to use pliers or a pipe wrench for extra grip.

AD

Inspect the threads on both the shower arm and the old showerhead to ensure they're free from any damage or rust. Repair or replace any faulty parts if necessary before proceeding.

Install the Extension Arm

Wrap the threads of the extension arm with Teflon tape. This plumber's tape helps create a watertight seal, preventing leaks and ensuring a secure connection. Wrap the tape clockwise, overlapping each layer by about one-third. Be generous but avoid over-applying as excess tape can clog the threads.

Attach the Extension Arm to the Shower Arm

Hand-tighten the extension arm onto the shower arm using your hands only. Do not overtighten; finger-tight plus a quarter turn is usually sufficient. Over-tightening can strip the threads and cause leaks.

AD

Now, temporarily install the showerhead onto the extension arm using the same process. If your extension arm has adjustment knobs, rotate them to position the showerhead at the desired height.

Re-attach the Water Supply and Test

Reconnect the water supply and turn it back on. Allow the water to run for a minute to wash out any remaining debris from the pipe. Then, turn off the water again.

Gently adjust the extension arm and showerhead to ensure they're secure and leaking-free. Turn the water back on and check for any leaks around the extension arm and showerhead connections. If there are leaks, re-secure the connections by hand-tightening further and reiterate the Teflon tape process if necessary.

AD

Enjoy your upgraded, perfectly positioned showerhead! Should any issues arise, don't hesitate to call a professional plumber. Minor adjustments can make a world of difference in your bathroom, enhancing your daily routine seamlessly.

AD