how to put wheels on pinewood derby car

Boost Your Race: Step-by-Step Guide to Attach Pinewood Derby Car Wheels

By Emily Harris
AD

So, you've decided to participate in a Pinewood Derby and want to know how to put wheels on a pinewood derby car? You're in the right place. We'll guide you through the process step by step, ensuring your car is ready to hit the track. Let's dive right in.

Before we start, you'll need to ensure you have the necessary tools and materials. This includes a pinewood derby car kit (body, wheels, and axles), axle washers, graphite powder, and a few basic tools like pliers, a hammer, and sandpaper. Now, let's get your car racing ready.

Preparing the Axles and Wheels

The first step is to prepare the axles and wheels for assembly. This involves deburring the axles and inspecting the wheels for any defects.

AD
How to Build a Fast Pinewood Derby Car
How to Build a Fast Pinewood Derby Car
a person using a pair of scissors to cut up some black plastic buttons on a wooden table
a person using a pair of scissors to cut up some black plastic buttons on a wooden table
instructions on how to use a drill
instructions on how to use a drill

Deburring the axles is simple. Use a deburring tool or a piece of fine sandpaper wrapped around a pencil to smooth out any sharp edges. This step is crucial to prevent the axles from damaging the wheels during assembly.

Inspecting the Wheels

Next, carefully inspect each wheel to ensure they are true (have no wobble) and round. Any imperfections could lead to poor performance in the race.

How To Raise A Wheel On A Pinewood Derby Car
How To Raise A Wheel On A Pinewood Derby Car
How to Polish Your Pinewood Derby Car's Axles and Wheels
How to Polish Your Pinewood Derby Car's Axles and Wheels

To check if the wheels are true, spin them gently on a flat surface. They should spin smoothly and not wobble. If they do, you may need to Sand the inner lip of the wheel until it no longer wobbles.

Assembling the Axle and Wheel

Now it's time to assemble the axles and wheels. Start by placing an axle washer onto the axle. The washer goes on first to prevent the wheel from being pushed onto the axle too far and making the car hang.

AD

Next, carefully place the wheel onto the axle. Gently pull the axle through the wheel, ensuring it's centered. The wheel should spin freely on the axle. If not, the axle may be too tight. In this case, use pliers to gently bend the axle slightly outward to loosen it.

Mounting the Axles to the Car

With the axles and wheels assembled, it's time to mount them to the car body.

Most pinewood derby car kits come with pre-drilled holes for the axles. However, these holes are usually too large and need to be narrowed to keep the axles from slipping. To do this, use a piece of fine sandpaper or a drill bit to gradually make the hole smaller until the axle fits snugly.

AD

Securing the Axles

Once the holes are narrowed, place the axle through the car body, ensuring the wheel is on the outside. Push the axle through until the washer touches the car body. Leave about 1/16 of an inch between the washer and the car body for free movement.

To secure the axle, carefully tap it gently with a hammer. The goal is not to bend the axle but to ensure the washer is snug against the car body. Be careful not to tap too hard, as this could bend the axle.

Checking for Square

After securing the axles, it's essential to check if your car is square. A car that rolls on a flat surface but stops when lifted slightly is not square. To check, lift one end of the car slightly while letting the other end roll on a flat surface. If it rolls smoothly, your car is square.

AD

If your car isn't square, you may need to adjust the axles or the car body until it rolls smoothly when lifted. This process may take some trial and error, but it's crucial for a fair race.

Preparing for the Race

With the axles and wheels secured, your car is now ready for race day. However, there's one more step to ensure peak performance.

Graphite powder is commonly used to lubricate the axles and reduce friction. Apply a small amount of graphite powder to the axle where it touches the washer. Also, Apply a small amount to the axle hole in the car body. This will help your car run smoothly on the track.

Final Touches

Before heading to the race, give your car a good once-over. Ensure all wheels spin freely and that your car is square. Also, give your car a unique design or paint job to make it stand out on the track.

Remember, the key to a successful Pinewood Derby is patience and attention to detail. Don't rush the process. Each step, from preparing the axles to checking for square, contributes to your car's performance. So, take your time, enjoy the process, and good luck at the race!

AD