How to Install Insinkerator Badger 5: A Step-by-Step Guide
Are you tired of standing in line at the sink, waiting for your turn to do dishes? It's time to install an InSinkErator Badger 5 food waste disposer and bid farewell to clogged pipes and smelly drains. This comprehensive guide will walk you through the simple process of installing your InSinkErator Badger 5, ensuring a perfect fit and optimal performance.
Before you start, make sure you have all the necessary tools at hand: pliers, adjustable wrench, screwdriver, and dishwasher drain connection kit. This guide assumes you have some basic DIY skills and a good understanding of your kitchen's plumbing. Let's dive right in!
Preparing the Workspace
Before you get started, make sure your workspace is clean and clear. Safety is paramount when dealing with sharp objects and electrical components, so ensure you're working in a well-lit, spacious area.
To prepare your sink, disconnect the drain line and remove the old disposal unit, if there was one. Don't forget to shut off the power to the circuit that controls the disposal to avoid any electrical accidents.
Removing the Old Disposal
Grab your adjustable wrench and loosen the mounting lugs that secure the disposal to the sink, then ease the unit out. If the old disposal is stuck or difficult to remove, you might need to use a hacksaw to cut away any old mounting screws.
Now, carefully unthread the drain tailpiece from the disposal's discharge tube. You might need to use a slight upward twist to break the seal. Once the tailpiece is loose, carefully remove it and discard any old plumber's putty.
Preparing the InSinkErator Badger 5
The Badger 5 comes with a universal mounting assembly, but you might need to swap out some parts depending on your sink's configuration. Check the included hardware and make any necessary adjustments before proceeding.
Tilt the Badger 5 so that the drain opening faces upwards. Apply a generous amount of plumber's putty around the bottom of the mounting ring. This will create a watertight seal between the disposal and the sink. Once you've applied the putty, position the mounting ring against the sink opening and twist gently to evenly distribute the putty.
Installing the InSinkErator Badger 5
With the putty applied and the mounting ring in place, it's time to secure the disposal to the sink. Using your hands, twist the disposal clockwise until the mounting lugs are snug against the bottom of the sink. Don't overtighten; you should be able to turn the disposal counterclockwise by about a quarter turn.
Now, secure the disposal to the sink using the included sink flange, backup ring, and mounting assembly. Thread the mounting assembly onto the disposal, placing the backup ring on top, followed by the sink flange. Tighten with your adjustable wrench, turning it clockwise.
Connecting the Drain Line
It's time to connect your InSinkErator Badger 5 to your kitchen's drain system. Locate the dishwasher drain connection kit and attach it to the bottom of the disposal. Tighten the fitting using your adjustable wrench, turning it clockwise.
Next, attach the discharge tube to the dishwasher drain connection kit. Ensure the tube's end is flush with the kit's fitting. If necessary, use pliers to bend the tube's end to fit tightly against the fitting.
Securing the Power Cable
Locate the power cable grommet and slide it onto the power cord. Fit the cord through the power opening in the mounting assembly, pulling it through until the grommet secures the cord in place.
Now, strip about 3/4 inch of insulation from the end of the power cable, exposing the wires inside. Twist the exposed wires clockwise around the captive mounting screws' heads. Ensure the wires are tightly secured, with no loose strands.
Reattach the power cord connector, ensuring it clicks into place. Once the power cable is secure, fold the cable back into the cavity of the disposal and secure it with the cable clamp. Double-check that all wires are safely tucked away within the disposal's cavity.
Testing Your InSinkErator Badger 5
Before turning the power back on, double-check that all connections are secure, and there are no loose wires. Once you're satisfied with your work, slowly turn the power back on at your fuse box or circuit breaker.
Run some cold water into the sink and let it drain to test the disposal. When the water drains, flip the switch to start the disposal. Let it run for a few seconds, then turn it off. Repeat this process a few times to ensure the Badger 5 is working correctly.
Congratulations! You've successfully installed your InSinkErator Badger 5. Now you can enjoy efficient food waste disposal and say goodbye to stubborn clogs. Regularly clean your disposal, and don't forget to run cold water while and after using it to help flush away food debris. Happy cooking!