how to install insinkerator

Step-by-Step Guide: How to Install an InSinkErator

By John Miller
AD

So, you've decided to upgrade your kitchen with an Insinkerator garbage disposal, haven't you? It's a fantastic way to reduce food waste and make cleaning up after meals a breeze. But before you can start enjoying these benefits, you need to know how to install your Insinkerator. Fret not, for we've got you covered with a simple, step-by-step guide.

Before we dive into the installation process, let's ensure you have all the necessary tools and parts. You'll need a screwdriver, pliers, a wrench, and, of course, your Insinkerator disposal unit. Additionally, you should have a supply tailpiece, mounting ring,onautomatic reset switch, and the correct power cord for your model.

Preparing the Site

The first step in installing your Insinkerator is to prepare the site. This involves removing the old disposal, if you have one, and ensuring the new one fits perfectly.

AD
How to Turn on Insinkerator
How to Turn on Insinkerator
How To Install A Garbage Disposal | InSinkErator Badger 5/500 Series
How To Install A Garbage Disposal | InSinkErator Badger 5/500 Series
Réduisez vos poubelles avec l'installation d'un broyeur @insinkerator House Cleaning Reels, Dream Kitchen
Réduisez vos poubelles avec l'installation d'un broyeur @insinkerator House Cleaning Reels, Dream Kitchen

If you're replacing an old disposal, unscrew the mounting bracket and remove the old unit. Then, check the spline on the drain output on your sink. It should match the one on your new Insinkerator. If not, you may need to replace the sink tailpiece.

Removing the Old Disposal

If you're replacing an old disposal, the process starts with removing it. First, power down your circuit breaker. Then, disconnect the power cord and the dishwasher connection, if applicable. Next, loosen and remove the mounting assembly. Finally, remove the old disposal unit.

Water Under Sink Filtration System
Water Under Sink Filtration System
How to install a Garbage Disposal Button - InSinkErator SinkTop Switch STS-SO
How to install a Garbage Disposal Button - InSinkErator SinkTop Switch STS-SO

If your old disposal causes any resistance, use a screwdriver or a disposal removal tool to unlock the impeller. The impeller should then spin easily, allowing you to remove the disposal.

Measuring and Preparing the Sink Opening

Measure the drain hole in your sink. It should match your Insinkerator's mounting assembly. If not, or if you have a special installation (like an under-counter mount), consult the Insinkerator installation guide for your specific model.

AD

Once you've confirmed a perfect fit, prepare the sink opening. Clean around and inside the drain hole, and ensure there's no debris or rust that could interfere with your installation.

Installing the Insinkerator

Now that your site is prepped, it's time to install your new Insinkerator.

Start by installing the mounting assembly. Connect the discharge lines to the dishwasher, if applicable. Then, insert the supply tailpiece into your sink tailpiece. Finally, tighten the screws on the mounting assembly to secure the unit firmly against the sink.

AD

Mounting the Insinkerator

Begin by placing the mounting ring onto the sink. Then, insert the upper part of the mounting assembly from underneath the sink. Push the mystery bushing (located under the sink) up into the opening of the mounting ring.

Next, slide the desludger tool onto the shaft of the impellers until it rests on the mounting ring. Then, from beneath the sink, turn the mounting nut onto the mystery bushing and tighten it securely. Ensure the unit is firmly against the sink and the flanges are flush.

Connecting the Power Cord

Connect the power cord to your new Insinkerator. Ensure you use the correct power cord for your model. Then, connect the dishwasher connection, if applicable. Remember to connect the green ground wire to the ground terminal.

AD

Next, follow your Insinkerator installation guide to connect the automatic reset switch to the power cord. Ensure the switch is placed on the wall, close to the disposal but out of the splash zone.

Testing Your Insinkerator

Before you power up your new disposal, there's one crucial test you must perform.

Check for leaks. While the unit is still disconnected from power, pour cold water down the drain and into the disposal. If water leaks out, tighten all connectors and check for any damage.

Powering Up and Running the Disposal

Once you've confirmed there are no leaks, you're ready to power up your new Insinkerator. Reconnect the circuit breaker. With the disposal turned off, turn on the cold water tap. Then, push down the lever on the disposal.

Listen for the disposal to grind, indicating it's working smoothly. Drop in small amounts of food waste, Continue listening, ensuring the disposal continues to work effectively.

Congratulations! You've successfully installed your Insinkerator garbage disposal. Now, you can enjoy the convenience and cleanliness it offers. Remember, always run cold water when using your disposal and avoid putting non-food items, like bones, down the drain.

So, go ahead, start cooking, and let your new Insinkerator do the clean-up. Happy cooking!"

AD