how to connect pex to shower valve

How to Connect PEX to Shower Valve: A Step-by-Step Guide

By Hannah Rodriguez
AD

Connecting PEX (Cross-Linked Polyethylene) to a shower valve may seem like a daunting task, but with the right steps and tools, it's a manageable DIY project that can save you money. PEX, a flexible and durable piping material, is becoming increasingly popular for plumbing due to its resistance to scale and chlorine, and its ability to reduce water noise. Here's a comprehensive guide on how to connect PEX to a shower valve.

Before you begin, make sure you have the right tools and materials. You'll need a tube cutter specifically designed for PEX, expansion rings, an expansion tool, stainless steel clamps, PEX pipe and fittings, and some Arsenal sandpaper for roughing up the pipe's outer surface to promote better adhesive binding.

Preparing the PEX Pipe

The first step is to prepare the PEX pipe. Measure and cut the PEX pipe to the required length using the PEX tube cutter. Ensure you cut the pipe squarely to get a clean edge that will facilitate a proper seal.

AD
How to - Install a Shower Valve using Pex Tubing Plumbing & Sharkbite connectors EASY - DELTA Faucet
How to - Install a Shower Valve using Pex Tubing Plumbing & Sharkbite connectors EASY - DELTA Faucet
DIY How to Install a Shower Valve using Pex Plumbing
DIY How to Install a Shower Valve using Pex Plumbing
How to Install a Shower Valve with PEX A and SharkBite Plumbing - BEGINNERS Guide
How to Install a Shower Valve with PEX A and SharkBite Plumbing - BEGINNERS Guide

Next, you need to prepare the ends of the PEX pipe for expansion fitting. Using the sandpaper, lightly rough up the outer surface of the PEX pipe at the points where the expansion fittings will be inserted. This helps to ensure a better bond between the pipe and the fitting.

Expansion Fitting Method

The expansion fitting method is the most common way to connect PEX to a shower valve. It's quick, easy, and requires no soldering or glue. Here's how to do it:

a close up of a person holding an electronic device with a pen in it's hand
a close up of a person holding an electronic device with a pen in it's hand

1. Insert the PEX pipe into the expansion fitting, pushing it in until it reaches the stop on the fitting. The fitting should be about 1 to 1.5 inches long along the PEX pipe.
2. Using the expansion tool, expand the fitting by sliding the tool over the fitting. This causes the fitting to grip the PEX pipe tightly, creating a secure and watertight connection.
3. Allow the fitting to cool for a few seconds before removing the expansion tool.
4. Clean up the fitting and pipe, removing any dust or debris.
5. Install the stainless steel clamp over the fitting and secure it in place with a screwdriver.

.br.use of Compression Fittings

While less common, compression fittings can also be used to connect PEX to a shower valve. These fittings require a PEX compression ring and a compression nut to secure the pipe in place.

AD

1. Screw the compression ring onto the PEX pipe, about an inch from the end.
2. Insert the PEX pipe into the compression fitting.
3. Tighten the compression nut onto the fitting. As you tighten, ensure the ring is properly seated in the fitting.
4. Continue tightening until the nut is snug, but be careful not to overtighten.

Connecting the PEX to the Shower Valve

Once you've prepared and connected the PEX pipe, it's time to install it into the shower valve. Most shower valves have PEX adaptors that thread directly onto the valve.

1. Slide the PEX pipe into the adaptors, ensuring they are fully seated in the expansion fitting or compression nut.
2. Use a wrench to tighten the adaptors onto the shower valve. Be careful not to overtighten and damage the valve.

AD

Checking for Leaks

After you've connected the PEX to the shower valve, it's crucial to check for leaks. Turn on the water and observe the connections closely. If there are no leaks, you've successfully connected your PEX to the shower valve.

If you do find a leak, you may need to tighten the connection or replace the fitting. In some cases, you may need to call a professional plumber to ensure the leak is resolved safely and effectively.

Remember, while this guide provides a general overview, each plumbing project is unique, and local building codes may require additional steps or specific fittings. Always consult with a professional if you're unsure about any aspect of your project. Happy DIYing!

AD
AD