how to change oil in ford escape

How to Change Oil in a Ford Escape

By Mark Taylor
AD

Regular oil changes are crucial for maintaining your Ford Escape's performance and longevity. Changing your oil at home can save you time and money, and it's not as daunting as it might seem. Here's a comprehensive guide on how to change oil in your Ford Escape.

Before starting, ensure you have all the necessary tools and materials. You'll need a wrench, an oil filter wrench, a drain pan, a funnel, around 5 liters of new oil suitable for your Escape (consult your owner's manual for the exact type), and a new oil filter.

Prepare Your Ford Escape for the Oil Change

Start by running your engine for about 10-15 minutes to warm up the oil. This makes it easier to drain and less likely to damage the new oil filter. Next, drive your Escape up to a park or onto a jack if you have a lift. Safety first, so chock the wheels and use a jack stand to secure it.

AD
Oil Change Ford Escape 🛢️
Oil Change Ford Escape 🛢️
How to change the oil and reset the oil life on a 2017 Ford Escape
How to change the oil and reset the oil life on a 2017 Ford Escape
2013 To 2019 Ford Escape How To Change Cargo Engine Oil & Filter With Part Numbers - Quick & Easy
2013 To 2019 Ford Escape How To Change Cargo Engine Oil & Filter With Part Numbers - Quick & Easy

Locate your oil pan and filter underneath your vehicle. They're usually at the bottom of the engine, near the front. Place your drain pan underneath the oil pan to catch the old oil.

Drain the Old Oil

Use your wrench to loosen and then remove the oil pan's drain plug by hand. Be careful; it may be hot. Allow the oil to drain completely, which can take a few minutes. Don't forget to replace the drain plug once all the oil is out.

Change the Oil on a Ford Escape
Change the Oil on a Ford Escape
2017 Ford Escape Oil Change
2017 Ford Escape Oil Change

Using your oil filter wrench, loosen and remove the old oil filter. If it's too tight, use the wrench to break the seal, then remove it by hand. Discard the old oil filter.

Replace the Oil Filter

Rub a small amount of new motor oil around the gasket of your new oil filter. This helps create a better seal and makes starting your engine easier. Screw on the new filter by hand, turning it clockwise for about ¾ of a turn.

AD

Before reinserting the drain plug, use a gasket scraper or a flathead screwdriver to clean the old gasket off the drain plug. Reinstall the plug by hand, then tighten it using the wrench. Be careful not to overtighten it.

Add New Oil to Your Ford Escape

Find the oil fill hole on top of your engine. It's typically near the rear of the engine, and there's a cap labeled "Oil." Unscrew the cap and place your funnel into the opening. Pour in the correct amount of oil, allowing it to settle before adding more.

Once you've added the correct amount of oil, let it settle for a few minutes. Remove the funnel and replace the oil fill cap. Lower your vehicle and start the engine. Let it run for about a minute to allow the new oil to circulate.

AD

Check the Oil Level

Turn off your engine and let it sit for about 10 minutes to allow the oil to settle completely. Locate your dipstick, pull it out, wipe it clean, then reinsert it all the way. After pulling it back out, check where the oil level falls on the dipstick. If it's between the "FULL" and "ADD" lines, you're good to go.

If your oil level is low, you may have overtightened the drain plug or the new oil filter. In this case, you might need to remove the drain plug, allow a little more oil to drain, and then replace the plug. After adding more oil, check the level again.

Regularly changing your Ford Escape's oil is a key part of maintaining its performance and longevity. Now that you know how to change oil in a Ford Escape, you're well on your way to keeping your vehicle in top shape. Don't forget, it's also a good idea to dispose of your used oil responsibly. Check with your local recycling center for guidelines.

AD
AD