how to backwash a de pool filter

Mastering Pool Care: How to Backwash Your Pool Filter

By Christopher Harris
AD

Regular maintenance of your inground swimming pool is crucial to ensure clarity, hygiene, and longevity of your pool equipment. One vital aspect of this maintenance is backwashing your pool filter. Backwashing your filter helps remove dirt, dust, and other particles that the filter media has collected, keeping your pool water sparkling clean. Let's delve into the intricacies of how to backwash a pool filter, providing a comprehensive guide that's easy to understand and follow.

Before we embark on the step-by-step process, let's demystify the concept of backwashing. Backwashing involves reversing the water flow through your filter, rinsing and removing the trapped contaminants. This process not only cleans your filter but also revitalizes it, lengthening its lifespan. Typically, pools with cartridge or diatomaceous earth (DE) filters require backwashing every one to two weeks, while sand filters need it less frequently, approximately every few months.

Preparation for Backwashing: Gathering Your Tools

Ensure you have the necessary tools before you start backwashing your pool filter. Gathering these tools beforehand will make the process smoother and more efficient.

AD
an image of a poster with the words how to backwash a de filter
an image of a poster with the words how to backwash a de filter
How to Backwash a Pool Filter
How to Backwash a Pool Filter
How Do You Backwash A Pool Filter?
How Do You Backwash A Pool Filter?

Here's a list of tools you'll need:

  • A electrical multimeter (optional but helpful for checking multivalve pressure)
  • Gloves to protect your hands from chemicals and dirty water
  • Goggles to shield your eyes from any debris or chemicals
  • Filter cleaning solution (for DE filters)
  • Sand (if you have a sand filter)

Pre-backwash Check: Valve and Filter Pressure

Before you start backwashing, ensure your multivalve is in the correct position. If it's not, switch it from 'filter' to 'backwash'.

How to Backwash a Sand Filter for a Super Clean Pool
How to Backwash a Sand Filter for a Super Clean Pool
How Do I Backwash a Sand Filter in My Fiberglass Pool? - Thursday Pools
How Do I Backwash a Sand Filter in My Fiberglass Pool? - Thursday Pools

Next, use an electrical multimeter to check the pressure on your filter. The pressure should be within the range stated in your pool's manual. If it's significantly higher, it might be due for backwashing.

SafetyConsiderations and Precautions

Before you proceed with backwashing, make sure to turn off your pool pump.

AD

Also, ensure that no one is swimming in the pool or nearby during the backwashing process. The water being released can be dirty and may contain chemicals that could cause irritation or harm.

The Backwashing Procedure: Step-by-Step

Now that you're all set, let's get into the actual process of backwashing your pool filter.

Remember, the exact steps might vary slightly depending on your pool filter type. Always consult your pool's manual for specific directions.

AD

Step 1: Initiate Backwashing

Open the backwash valve on your pool filter system. This will reverse the water flow, cleaning the filter media.

The water will start to flow out through the waste line, carrying with it the trapped contaminants in your filter.

Step 2: Monitor Progress

Keep an eye on the filter. The water should turn murky and then gradually clear up as the filter is cleaned.

AD

The backwashing process usually takes several minutes, depending on how dirty your filter is.

Rinsing and Priming Your Filter

After backwashing, your filter needs to be rinsed and primed to ready it for another cycle of filtering your pool water.

This process is quite straightforward and varies slightly based on the type of filter you have.

Cartridge and DE Filters: Rinse and Prime

Once the water running out of the waste line is clear, switch the multivalve to 'rinse'. This will pump water back through the filter to clean it, dislodging any remaining debris.

Then, switch to 'waste' until clear water runs out. Finally, switch back to 'filter', allowing the filter to prime.

Sand Filters: Refill and Vacuum

After backwashing, your sand filter needs to be refilled and vacuumed to close the system.

Start by switching your multivalve from 'backwash' to 'rinse'. Then, refill the filter with water to the appropriate level.

Finally, vacuum the sand from the bottom of your filter and discard it. Replace the drain plug and restart your pool pump.

Regular backwashing is a vital part of maintaining your inground swimming pool. By following this guide, you can keep your pool water crystal clear and your filter system functioning at its best. Remember, always consult your pool's manual for specific direction related to your pool. Happy swimming!

AD