how to adjust governor on briggs and stratton 8hp

How to Adjust Governor on Briggs & Stratton 8HP

By Thomas Brown
AD

Getting the most out of your Briggs & Stratton 8HP engine involves regular maintenance, one of which is adjusting the governor. The governor controls the engine's speed, and when it's off, it can cause your lawn mower or other equipment to stall or run too fast. Here's a step-by-step guide to help you adjust the governor on your Briggs & Stratton 8HP engine.

Before we start, ensure the engine is cool and that you have the right tools. You'll need a flathead screwdriver, a 3/8-inch nut driver, and a feeler gauge. For your safety, always disconnect the spark plug wire and ground it before servicing your engine.

Understanding the Governor System

The governor system on your Briggs & Stratton 8HP engine consists of a governor lever, a governor arm, and a governor spring. The governor lever controls the engine speed, while the governor spring determines the engine's high-speed limit.

AD
Briggs and Stratton 5HP - Governor Adjustment - Model 135202
Briggs and Stratton 5HP - Governor Adjustment - Model 135202
How a Briggs and Stratton Push Mower engine governor/throttle linkage is set up, and how it works.
How a Briggs and Stratton Push Mower engine governor/throttle linkage is set up, and how it works.
How to adjust valves on an OHV Briggs
How to adjust valves on an OHV Briggs

Adjusting the governor involves fine-tuning these components to ensure your engine runs at the correct RPM. This guide will help you adjust the governor lever and the governor spring, two key components in maintaining your engine's speed.

Adjusting the Governor Lever

To adjust the governor lever, first, locate it on the side of the engine. It's connected to the governor arm and the governor linkage. Use your flathead screwdriver to gently pry the governor lever from its current position. You may need to use a slight twisting motion to free it.

How to Repair a Briggs & Stratton Starter Mower
How to Repair a Briggs & Stratton Starter Mower
HOW THE GOVERNOR works on a Briggs Stratton engine. How to adjust the idle and High-Speed John Deere
HOW THE GOVERNOR works on a Briggs Stratton engine. How to adjust the idle and High-Speed John Deere

Once freed, carefully move the governor lever to the right to increase the engine's speed, or to the left to decrease it. After making your adjustment, try running the engine and observe its speed. It should run smoothly at around 3,600 RPM at wide-open throttle.

Adjusting the Governor Spring

The governor spring determines the engine's high-speed limit. If your engine is over-revving, you'll need to adjust the governor spring. First, locate the governor spring adjustment screw, usually identified by a 'G' on the engine's side or oil fill cap.

AD

Using your 3/8-inch nut driver, carefully loosen the adjustment screw. To increase the governor spring tension, turn the screw clockwise. To decrease it, turn it counterclockwise. After adjusting, try running the engine and observe its high-speed limit. It should not exceed 4,000 RPM.

Inspecting and Maintaining the Governor System

Regularly inspecting the governor system can help prevent future issues. Look for any signs of wear or damage on the governor lever, governor arm, and governor linkage. If any components are worn or damaged, they should be replaced immediately.

Also, ensure that all governor components are properly lubricated. A lack of lubrication can cause excessive wear and tear, leading to governor system failure. Use a light engine oil to lubricate the governor linkage and a high-temperature grease for the governor adjustment screws.

AD

Using a Feeler Gauge to Check Clearance

After adjusting the governor, it's a good practice to check the clearance between the governor lever and the governor arm using a feeler gauge. This ensures that the governor is operating correctly and that there's no excess play in the governor linkage.

With the engine running at wide-open throttle, insert the feeler gauge between the governor lever and the governor arm. The clearance should be between 0.010 and 0.015 inches. If the clearance is outside this range, you may need to re-adjust the governor.

Congratulations, you've successfully adjusted and maintained the governor on your Briggs & Stratton 8HP engine! Remember, regular maintenance and adjustments are key to keeping your engine running smoothly and maximizing its lifespan. Always refer to your engine's owner's manual for specific details about your model. Happy mowing!

AD
AD