maytag washer how to remove agitator

Maytag Washer: How to Remove an Agitator

By Mark Hernandez
AD

atlas> is a common question among Maytag washer owners is how to remove the agitator. The agitator, found in top-loading washers, plays a crucial role in mixing clothes and detergent during the wash cycle. However, it can sometimes become worn out, damaged, or simply need replacing. Understanding how to remove it can help save you the cost and inconvenience of calling a professional.

Before you begin, make sure your washer is empty, unplugged, and the water supply is turned off to ensure your safety. It's also a good idea to gather some basic tools like a screwdriver, pliers, and a towel to absorb any water.

Preparation and Accessing the Agitator

The first step in removing the agitator is to prepare your washer and gain access to the agitator itself.

AD
Where is the filter on your Maytag washer top loader (no agitator model)?
Where is the filter on your Maytag washer top loader (no agitator model)?
How to remove agitator from Maytag washer mvwc565fw1?
How to remove agitator from Maytag washer mvwc565fw1?
Maytag Washer Won't Agitate? Here's How To Fix It
Maytag Washer Won't Agitate? Here's How To Fix It

Begin by shutting off the water supply valves located behind the washer. Then, unplug the washer from the power source to avoid any electrical hazards.

Draining the Washer

To drain any water remaining in the washer, place a bucket or large bowl beneath the drainage pump. Use a screwdriver or pliers to loosen and remove the drainage pump tube situated at the bottom of the washer. Allow the water to drain completely into the bucket.

Repair Washer Agitator, How To Clean Agitator In Washer, How To Replace Agitator On Whirlpool Washer, How To Replace Washing Machine Agitator, How To Repair Maytag Washing Machines, How To Fix Maytag Washing Machine, How To Clean Washing Machine Agitator, Ge Washer Agitator Replacement Instructions, How To Replace Washing Machine Stator
Repair Washer Agitator, How To Clean Agitator In Washer, How To Replace Agitator On Whirlpool Washer, How To Replace Washing Machine Agitator, How To Repair Maytag Washing Machines, How To Fix Maytag Washing Machine, How To Clean Washing Machine Agitator, Ge Washer Agitator Replacement Instructions, How To Replace Washing Machine Stator
Removing Maytag washer Agitator
Removing Maytag washer Agitator

After the water has drained, use a towel to absorb any remaining moisture from the washer's interior.

Removing the Washer's Top Panel

Once the washer is drained, the next step is to remove the top panel. For Maytag washers, this usually involves unscrewing a few screws hidden under the top panel's plastic trim. You can gently pry off the trim using a flathead screwdriver if necessary.

AD

With the screws removed, lift the top panel off the washer. You should now have clear access to the agitator.

Removing the Agitator

With the top panel removed, you're now ready to disconnect and remove the agitator. The process involves several steps, so take your time to avoid damaging any components.

Before proceeding, it's a good idea to have a new agitator or the necessary replacement parts on hand to ensure a smooth replacement process.

AD

Disconnecting the Drive.amazonaws

The agitator is connected to the washer's motor via a drive shaft. To remove it, you'll first need to disconnect this shaft. You might need a wrench or socket to loosen the set screw holding the drive shaft in place. Once the set screw is loosened, you can pull out the drive shaft or turn it counterclockwise to remove it from the agitator.

Be cautious when handling the drive shaft, as it may still be attached to the washer's motor. Support the motor as you work to prevent straining its internal components.

Removing the Agitator

With the drive shaft disconnected, you can now remove the agitator itself. Look for retaining nuts or screws at the base of the agitator. These may be hidden beneath a decorative cap or hidden by the washer's tub. Remove these fasteners to release the agitator.

AD

If your agitator is stuck, you can try wiggling it gently or using a rubber mallet to tap it gently. Never use force, as this could damage the washer's inner tub or other components. Once the agitator is loose, gently pull it up and out of the washer.

Testing and Reinstallation

Before reinstalling the new agitator, take the time to test your Maytag washer to ensure everything is working correctly.

First, reattach the drive shaft to the new agitator, ensuring it's securely in place. Then, reinsert the agitator into the washer's tub, replacing the retainer nuts or screws, and tightening them securely.

Reassembly

With the new agitator secured, you can now begin reassembling your Maytag washer. Start by replacing the top panel, ensuring it's properly aligned and secured with the screws you removed earlier.

Once the top panel is in place, you can reconnect the drainage pump tube and water supply valves. Finally, plug in your washer and give it a test run to ensure the new agitator is working correctly.

Remember, always refer to your Maytag washer's owner's manual for model-specific instructions, as the process may vary slightly depending on your washer's make and model. If you're unsure about any step, don't hesitate to consult a professional appliance repair technician.

There you have it – a step-by-step guide to removing and replacing the agitator in your Maytag washer. With a little patience and careful attention to detail, you can save yourself the cost and inconvenience of calling a professional. Happy washing!

AD